Kconfig 19.6 KB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560
if ETRAX_ARCH_V10

config ETRAX_ETHERNET
	bool "Ethernet support"
	depends on ETRAX_ARCH_V10 && NETDEVICES
	select MII
	help
	  This option enables the ETRAX 100LX built-in 10/100Mbit Ethernet
	  controller.

config ETRAX_SERIAL
	bool "Serial-port support"
	depends on ETRAX_ARCH_V10
	help
	  Enables the ETRAX 100 serial driver for ser0 (ttyS0)
	  You probably want this enabled.

config ETRAX_SERIAL_FAST_TIMER
	bool "Use fast timers for serial DMA flush (experimental)"
	depends on ETRAX_SERIAL
	help
	  Select this to have the serial DMAs flushed at a higher rate than
	  normally, possible by using the fast timer API, the timeout is
	  approx. 4 character times.
	  If unsure, say N.

config ETRAX_SERIAL_FLUSH_DMA_FAST
	bool "Fast serial port DMA flush"
	depends on ETRAX_SERIAL && !ETRAX_SERIAL_FAST_TIMER
	help
	  Select this to have the serial DMAs flushed at a higher rate than
	  normally possible through a fast timer interrupt (currently at
	  15360 Hz).
	  If unsure, say N.

config ETRAX_SERIAL_RX_TIMEOUT_TICKS
	int "Receive flush timeout (ticks) "
	depends on ETRAX_SERIAL && !ETRAX_SERIAL_FAST_TIMER && !ETRAX_SERIAL_FLUSH_DMA_FAST
	default "5"
	help
	  Number of timer ticks between flush of receive fifo (1 tick = 10ms).
	  Try 0-3 for low latency applications.  Approx 5 for high load
	  applications (e.g. PPP).  Maybe this should be more adaptive some
	  day...

config ETRAX_SERIAL_PORT0
	bool "Serial port 0 enabled"
	depends on ETRAX_SERIAL
	help
	  Enables the ETRAX 100 serial driver for ser0 (ttyS0)
	  Normally you want this on, unless you use external DMA 1 that uses
	  the same DMA channels.

choice
	prompt "Ser0 DTR, RI, DSR and CD assignment"
	depends on ETRAX_SERIAL_PORT0
	default ETRAX_SER0_DTR_RI_DSR_CD_ON_NONE

config ETRAX_SER0_DTR_RI_DSR_CD_ON_NONE
	bool "No_DTR_RI_DSR_CD"

config ETRAX_SER0_DTR_RI_DSR_CD_ON_PA
	bool "DTR_RI_DSR_CD_on_PA"

config ETRAX_SER0_DTR_RI_DSR_CD_ON_PB
	bool "DTR_RI_DSR_CD_on_PB"
	help
	  Enables the status and control signals DTR, RI, DSR and CD on PB for
	  ser0.

config ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	bool "DTR_RI_DSR_CD_mixed_on_PA_and_PB"

endchoice

config ETRAX_SER0_DTR_ON_PA_BIT
	int "Ser0 DTR on PA bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT0
	default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	default "4" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED

config ETRAX_SER0_RI_ON_PA_BIT
	int "Ser0 RI  on PA bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT0
	default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	default "5" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED

config ETRAX_SER0_DSR_ON_PA_BIT
	int "Ser0 DSR on PA bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT0
	default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	default "6" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED

config ETRAX_SER0_CD_ON_PA_BIT
	int "Ser0 CD  on PA bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT0
	default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	default "7" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PA || ETRAX_SER0_DTR_RI_DSR_CD_MIXED

config ETRAX_SER0_DTR_ON_PB_BIT
	int "Ser0 DTR on PB bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT0
	default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	default "4" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PB port to carry the DTR signal for serial
	  port 0.

config ETRAX_SER0_RI_ON_PB_BIT
	int "Ser0 RI  on PB bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT0
	default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	default "5" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PB port to carry the RI signal for serial
	  port 0.

config ETRAX_SER0_DSR_ON_PB_BIT
	int "Ser0 DSR on PB bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT0
	default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	default "6" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PB port to carry the DSR signal for serial
	  port 0.

config ETRAX_SER0_CD_ON_PB_BIT
	int "Ser0 CD  on PB bit (-1 = not used)" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT0
	default "-1" if !ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	default "7" if ETRAX_SER0_DTR_RI_DSR_CD_ON_PB || ETRAX_SER0_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PB port to carry the CD signal for serial
	  port 0.

config ETRAX_SERIAL_PORT1
	bool "Serial port 1 enabled"
	depends on ETRAX_SERIAL
	help
	  Enables the ETRAX 100 serial driver for ser1 (ttyS1).

choice
	prompt "Ser1 DTR, RI, DSR and CD assignment"
	depends on ETRAX_SERIAL_PORT1
	default ETRAX_SER1_DTR_RI_DSR_CD_ON_NONE

config ETRAX_SER1_DTR_RI_DSR_CD_ON_NONE
	bool "No_DTR_RI_DSR_CD"

config ETRAX_SER1_DTR_RI_DSR_CD_ON_PA
	bool "DTR_RI_DSR_CD_on_PA"

config ETRAX_SER1_DTR_RI_DSR_CD_ON_PB
	bool "DTR_RI_DSR_CD_on_PB"
	help
	  Enables the status and control signals DTR, RI, DSR and CD on PB for
	  ser1.

config ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	bool "DTR_RI_DSR_CD_mixed_on_PA_and_PB"

endchoice

config ETRAX_SER1_DTR_ON_PA_BIT
	int "Ser1 DTR on PA bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT1
	default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	default "4" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED

config ETRAX_SER1_RI_ON_PA_BIT
	int "Ser1 RI  on PA bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT1
	default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	default "5" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED

config ETRAX_SER1_DSR_ON_PA_BIT
	int "Ser1 DSR on PA bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT1
	default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	default "6" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED

config ETRAX_SER1_CD_ON_PA_BIT
	int "Ser1 CD  on PA bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT1
	default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	default "7" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PA || ETRAX_SER1_DTR_RI_DSR_CD_MIXED

config ETRAX_SER1_DTR_ON_PB_BIT
	int "Ser1 DTR on PB bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT1
	default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	default "4" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PB port to carry the DTR signal for serial
	  port 1.

config ETRAX_SER1_RI_ON_PB_BIT
	int "Ser1 RI  on PB bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT1
	default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	default "5" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PB port to carry the RI signal for serial
	  port 1.

config ETRAX_SER1_DSR_ON_PB_BIT
	int "Ser1 DSR on PB bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT1
	default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	default "6" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PB port to carry the DSR signal for serial
	  port 1.

config ETRAX_SER1_CD_ON_PB_BIT
	int "Ser1 CD  on PB bit (-1 = not used)" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT1
	default "-1" if !ETRAX_SER1_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	default "7" if ETRAX_SER1_DTR_RI_DSR_CD_ON_PB || ETRAX_SER1_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PB port to carry the CD signal for serial
	  port 1.

comment "Make sure you do not have the same PB bits more than once!"
	depends on ETRAX_SERIAL && ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && ETRAX_SER1_DTR_RI_DSR_CD_ON_PB

config ETRAX_SERIAL_PORT2
	bool "Serial port 2 enabled"
	depends on ETRAX_SERIAL
	help
	  Enables the ETRAX 100 serial driver for ser2 (ttyS2).

choice
	prompt "Ser2 DTR, RI, DSR and CD assignment"
	depends on ETRAX_SERIAL_PORT2
	default ETRAX_SER2_DTR_RI_DSR_CD_ON_NONE

config ETRAX_SER2_DTR_RI_DSR_CD_ON_NONE
	bool "No_DTR_RI_DSR_CD"

config ETRAX_SER2_DTR_RI_DSR_CD_ON_PA
	bool "DTR_RI_DSR_CD_on_PA"
	help
	  Enables the status and control signals DTR, RI, DSR and CD on PA for
	  ser2.

config ETRAX_SER2_DTR_RI_DSR_CD_ON_PB
	bool "DTR_RI_DSR_CD_on_PB"

config ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	bool "DTR_RI_DSR_CD_mixed_on_PA_and_PB"

endchoice

config ETRAX_SER2_DTR_ON_PA_BIT
	int "Ser2 DTR on PA bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT2
	default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	default "4" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PA port to carry the DTR signal for serial
	  port 2.

config ETRAX_SER2_RI_ON_PA_BIT
	int "Ser2 RI  on PA bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT2
	default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	default "5" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PA port to carry the RI signal for serial
	  port 2.

config ETRAX_SER2_DSR_ON_PA_BIT
	int "Ser2 DSR on PA bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT2
	default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	default "6" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PA port to carry the DTR signal for serial
	  port 2.

config ETRAX_SER2_CD_ON_PA_BIT
	int "Ser2 CD  on PA bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT2
	default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PA && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	default "7" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PA || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	help
	  Specify the pin of the PA port to carry the CD signal for serial
	  port 2.

config ETRAX_SER2_DTR_ON_PB_BIT
	int "Ser2 DTR on PB bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT2
	default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	default "4" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED

config ETRAX_SER2_RI_ON_PB_BIT
	int "Ser2 RI  on PB bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT2
	default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	default "5" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED

config ETRAX_SER2_DSR_ON_PB_BIT
	int "Ser2 DSR on PB bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT2
	default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	default "6" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED

config ETRAX_SER2_CD_ON_PB_BIT
	int "Ser2 CD  on PB bit (-1 = not used)" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT2
	default "-1" if !ETRAX_SER2_DTR_RI_DSR_CD_ON_PB && !ETRAX_SER2_DTR_RI_DSR_CD_MIXED
	default "7" if ETRAX_SER2_DTR_RI_DSR_CD_ON_PB || ETRAX_SER2_DTR_RI_DSR_CD_MIXED

config ETRAX_SERIAL_PORT3
	bool "Serial port 3 enabled"
	depends on ETRAX_SERIAL
	help
	  Enables the ETRAX 100 serial driver for ser3 (ttyS3).

choice
	prompt "Ser3 DTR, RI, DSR and CD assignment"
	depends on ETRAX_SERIAL_PORT3
	default ETRAX_SER3_DTR_RI_DSR_CD_ON_NONE

config ETRAX_SER3_DTR_RI_DSR_CD_ON_NONE
	bool "No_DTR_RI_DSR_CD"

config ETRAX_SER3_DTR_RI_DSR_CD_ON_PA
	bool "DTR_RI_DSR_CD_on_PA"

config ETRAX_SER3_DTR_RI_DSR_CD_ON_PB
	bool "DTR_RI_DSR_CD_on_PB"

config ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	bool "DTR_RI_DSR_CD_mixed_on_PA_and_PB"

endchoice

config ETRAX_SER3_DTR_ON_PA_BIT
	int "Ser3 DTR on PA bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PA || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT3
	default "-1"

config ETRAX_SER3_RI_ON_PA_BIT
	int "Ser3 RI  on PA bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PA || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT3
	default "-1"

config ETRAX_SER3_DSR_ON_PA_BIT
	int "Ser3 DSR on PA bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PA || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT3
	default "-1"

config ETRAX_SER3_CD_ON_PA_BIT
	int "Ser3 CD  on PA bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PA || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT3
	default "-1"

config ETRAX_SER3_DTR_ON_PB_BIT
	int "Ser3 DTR on PB bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PB || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT3
	default "-1"

config ETRAX_SER3_RI_ON_PB_BIT
	int "Ser3 RI  on PB bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PB || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT3
	default "-1"

config ETRAX_SER3_DSR_ON_PB_BIT
	int "Ser3 DSR on PB bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PB || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT3
	default "-1"

config ETRAX_SER3_CD_ON_PB_BIT
	int "Ser3 CD  on PB bit (-1 = not used)" if ETRAX_SER3_DTR_RI_DSR_CD_ON_PB || ETRAX_SER3_DTR_RI_DSR_CD_MIXED
	depends on ETRAX_SERIAL_PORT3
	default "-1"

config ETRAX_RS485
	bool "RS-485 support"
	depends on ETRAX_SERIAL
	help
	  Enables support for RS-485 serial communication.  For a primer on
	  RS-485, see <http://en.wikipedia.org/wiki/Rs485>

config ETRAX_RS485_ON_PA
	bool "RS-485 mode on PA"
	depends on ETRAX_RS485
	help
	  Control Driver Output Enable on RS485 transceiver using a pin on PA
	  port:
	  Axis 2400/2401 uses PA 3.

config ETRAX_RS485_ON_PA_BIT
	int "RS-485 mode on PA bit"
	depends on ETRAX_RS485_ON_PA
	default "3"
	help
	  Control Driver Output Enable on RS485 transceiver using a this bit
	  on PA port.

config ETRAX_RS485_DISABLE_RECEIVER
	bool "Disable serial receiver"
	depends on ETRAX_RS485
	help
	  It's necessary to disable the serial receiver to avoid serial
	  loopback.  Not all products are able to do this in software only.
	  Axis 2400/2401 must disable receiver.

config ETRAX_USB_HOST
	bool "USB host"
	select USB
	help
	   This option enables the host functionality of the ETRAX 100LX
	   built-in USB controller. In host mode the controller is designed
	   for CTRL and BULK traffic only, INTR traffic may work as well
	   however (depending on the requirements of timeliness).

config ETRAX_PTABLE_SECTOR
	int "Byte-offset of partition table sector"
	depends on ETRAX_AXISFLASHMAP
	default "65536"
	help
	  Byte-offset of the partition table in the first flash chip.
	  The default value is 64kB and should not be changed unless
	  you know exactly what you are doing. The only valid reason
	  for changing this is when the flash block size is bigger
	  than 64kB (e.g. when using two parallel 16 bit flashes).

config ETRAX_I2C
	bool "I2C support"
	depends on ETRAX_ARCH_V10
	help
	  Enables an I2C driver on ETRAX100.
	  EXAMPLE usage:
	  i2c_arg = I2C_WRITEARG(STA013_WRITE_ADDR, reg, val);
	  ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_WRITEREG), i2c_arg);
	  i2c_arg = I2C_READARG(STA013_READ_ADDR, reg);
	  val = ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_READREG), i2c_arg);

# this is true for most products since PB-I2C seems to be somewhat
# flawed..
config ETRAX_I2C_USES_PB_NOT_PB_I2C
	bool "I2C uses PB not PB-I2C"
	depends on ETRAX_I2C
	help
	  Select whether to use the special I2C mode in the PB I/O register or
	  not.  This option needs to be selected in order to use some drivers
	  that access the I2C I/O pins directly instead of going through the
	  I2C driver, like the DS1302 realtime-clock driver.  If you are
	  uncertain, choose Y here.

config ETRAX_I2C_DATA_PORT
	int "I2C SDA bit number"
	depends on ETRAX_I2C_USES_PB_NOT_PB_I2C
	default "0"
	help
	  Selects the pin on Port B where the data pin is connected

config ETRAX_I2C_CLK_PORT
	int "I2C SCL bit number"
	depends on ETRAX_I2C_USES_PB_NOT_PB_I2C
	default "1"
	help
	  Select the pin on Port B where the clock pin is connected

config ETRAX_I2C_EEPROM
	bool "I2C EEPROM (non-volatile RAM) support"
	depends on ETRAX_I2C
	help
	  Enables I2C EEPROM (non-volatile RAM) on PB0 and PB1 using the I2C
	  driver.  Select size option: Probed, 2k, 8k, 16k.
	  (Probing works for 2k and 8k but not that well for 16k)

choice
	prompt "EEPROM size"
	depends on ETRAX_I2C_EEPROM
	default ETRAX_I2C_EEPROM_PROBE

config ETRAX_I2C_EEPROM_PROBE
	bool "Probed"
	help
	  Specifies size or auto probe of the EEPROM size.
	  Options: Probed, 2k, 8k, 16k.
	  (Probing works for 2k and 8k but not that well for 16k)

config ETRAX_I2C_EEPROM_2KB
	bool "2kB"
	help
	  Use a 2kB EEPROM.

config ETRAX_I2C_EEPROM_8KB
	bool "8kB"
	help
	  Use a 8kB EEPROM.

config ETRAX_I2C_EEPROM_16KB
	bool "16kB"
	help
	  Use a 16kB EEPROM.

endchoice

config ETRAX_GPIO
	bool "GPIO support"
	depends on ETRAX_ARCH_V10
	---help---
	  Enables the ETRAX general port device (major 120, minors 0 and 1).
	  You can use this driver to access the general port bits. It supports
	  these ioctl's:
	  #include <linux/etraxgpio.h>
	  fd = open("/dev/gpioa", O_RDWR); // or /dev/gpiob
	  ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_SETBITS), bits_to_set);
	  ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_CLRBITS), bits_to_clear);
	  val = ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_READBITS), NULL);
	  Remember that you need to setup the port directions appropriately in
	  the General configuration.

config ETRAX_PA_CHANGEABLE_DIR
	hex "PA user changeable dir mask"
	depends on ETRAX_GPIO
	default "00"
	help
	  This is a bitmask with information of what bits in PA that a user
	  can change direction on using ioctl's.
	  Bit set = changeable.
	  You probably want 00 here.

config ETRAX_PA_CHANGEABLE_BITS
	hex "PA user changeable bits mask"
	depends on ETRAX_GPIO
	default "FF"
	help
	  This is a bitmask with information of what bits in PA that a user
	  can change the value on using ioctl's.
	  Bit set = changeable.
	  You probably want 00 here.

config ETRAX_PB_CHANGEABLE_DIR
	hex "PB user changeable dir mask"
	depends on ETRAX_GPIO
	default "00"
	help
	  This is a bitmask with information of what bits in PB that a user
	  can change direction on using ioctl's.
	  Bit set = changeable.
	  You probably want 00 here.

config ETRAX_PB_CHANGEABLE_BITS
	hex "PB user changeable bits mask"
	depends on ETRAX_GPIO
	default "FF"
	help
	  This is a bitmask with information of what bits in PB that a user
	  can change the value on using ioctl's.
	  Bit set = changeable.
	  You probably want 00 here.

endif