README.dual-flash
4 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
SPI/QSPI Dual flash connection modes:
=====================================
This describes how SPI/QSPI flash memories are connected to a given
controller in a single chip select line.
Current spi_flash framework supports, single flash memory connected
to a given controller with single chip select line, but there are some
hw logics(ex: xilinx zynq qspi) that describes two/dual memories are
connected with a single chip select line from a controller.
"dual_flash" from include/spi.h describes these types of connection mode
Possible connections:
--------------------
SF_SINGLE_FLASH:
- single spi flash memory connected with single chip select line.
+------------+ CS +---------------+
| |----------------------->| |
| Controller | I0[3:0] | Flash memory |
| SPI/QSPI |<======================>| (SPI/QSPI) |
| | CLK | |
| |----------------------->| |
+------------+ +---------------+
SF_DUAL_STACKED_FLASH:
- dual spi/qspi flash memories are connected with a single chipselect
line and these two memories are operating stacked fasion with shared buses.
- xilinx zynq qspi controller has implemented this feature [1]
+------------+ CS +---------------+
| |---------------------->| |
| | I0[3:0] | Upper Flash |
| | +=========>| memory |
| | | CLK | (SPI/QSPI) |
| | | +---->| |
| Controller | CS | | +---------------+
| SPI/QSPI |------------|----|---->| |
| | I0[3:0] | | | Lower Flash |
| |<===========+====|====>| memory |
| | CLK | | (SPI/QSPI) |
| |-----------------+---->| |
+------------+ +---------------+
- two memory flash devices should has same hw part attributes (like size,
vendor..etc)
- Configurations:
on LQSPI_CFG register, Enable TWO_MEM[BIT:30] on LQSPI_CFG
Enable U_PAGE[BIT:28] if U_PAGE flag set - upper memory
Disable U_PAGE[BIT:28] if U_PAGE flag unset - lower memory
- Operation:
accessing memories serially like one after another.
by default, if U_PAGE is unset lower memory should accessible,
once user wants to access upper memory need to set U_PAGE.
SPI_FLASH_CONN_DUALPARALLEL:
- dual spi/qspi flash memories are connected with a single chipselect
line and these two memories are operating parallel with separate buses.
- xilinx zynq qspi controller has implemented this feature [1]
+-------------+ CS +---------------+
| |---------------------->| |
| | I0[3:0] | Upper Flash |
| |<=====================>| memory |
| | CLK | (SPI/QSPI) |
| |---------------------->| |
| Controller | CS +---------------+
| SPI/QSPI |---------------------->| |
| | I0[3:0] | Lower Flash |
| |<=====================>| memory |
| | CLK | (SPI/QSPI) |
| |---------------------->| |
+-------------+ +---------------+
- two memory flash devices should has same hw part attributes (like size,
vendor..etc)
- Configurations:
Need to enable SEP_BUS[BIT:29],TWO_MEM[BIT:30] on LQSPI_CFG register.
- Operation:
Even bits, i.e. bit 0, 2, 4 ., of a data word is located in the lower memory
and odd bits, i.e. bit 1, 3, 5, ., of a data word is located in the upper memory.
Note: Technically there is only one CS line from the controller, but
zynq qspi controller has an internal hw logic to enable additional CS
when controller is configured for dual memories.
[1] http://www.xilinx.com/support/documentation/user_guides/ug585-Zynq-7000-TRM.pdf
--
Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
05-01-2014.