bf533-ezkit.h
2.91 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
/*
* U-boot - Configuration file for BF533 EZKIT board
*/
#ifndef __CONFIG_BF533_EZKIT_H__
#define __CONFIG_BF533_EZKIT_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf533-0.3
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 27000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 22
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
/*
* Memory Settings
*/
#define CONFIG_MEM_SIZE 32
/* Early EZKITs had 32megs, but later have 64megs */
#if (CONFIG_MEM_SIZE == 64)
# define CONFIG_MEM_ADD_WDTH 10
#else
# define CONFIG_MEM_ADD_WDTH 9
#endif
#define CONFIG_EBIU_SDRRC_VAL 0x398
#define CONFIG_EBIU_SDGCTL_VAL 0x91118d
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
/*
* Network Settings
*/
#define ADI_CMDS_NETWORK 1
#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x20310300
#define SMC91111_EEPROM_INIT() \
do { \
bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \
bfin_write_FIO_FLAG_C(PF1); \
bfin_write_FIO_FLAG_S(PF0); \
SSYNC(); \
} while (0)
#define CONFIG_HOSTNAME bf533-ezkit
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
* Flash Settings
*/
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SYS_MAX_FLASH_BANKS 3
#define CONFIG_SYS_MAX_FLASH_SECT 40
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR 0x20030000
#define CONFIG_ENV_SECT_SIZE 0x10000
#define FLASH_TOT_SECT 40
/*
* I2C Settings
*/
#define CONFIG_SYS_I2C_SOFT
#ifdef CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C
#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0
#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#endif
/*
* Misc Settings
*/
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif