6b13f685e
 김민수
BSP 최초 추가
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
|
#
# Copyright (C) 2007-2010, 2011-2012 Synopsys, Inc. (www.synopsys.com)
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License version 2 as
# published by the Free Software Foundation.
#
menuconfig ARC_PLAT_FPGA_LEGACY
bool "\"Legacy\" ARC FPGA dev Boards"
select ISS_SMP_EXTN if SMP
help
Support for ARC development boards, provided by Synopsys.
These are based on FPGA or ISS. e.g.
- ARCAngel4
- ML509
- MetaWare ISS
if ARC_PLAT_FPGA_LEGACY
config ARC_BOARD_ANGEL4
bool "ARC Angel4"
default y
help
ARC Angel4 FPGA Ref Platform (Xilinx Virtex Based)
config ARC_BOARD_ML509
bool "ML509"
help
ARC ML509 FPGA Ref Platform (Xilinx Virtex-5 Based)
config ISS_SMP_EXTN
bool "ARC SMP Extensions (ISS Models only)"
default n
depends on SMP
help
SMP Extensions to ARC700, in a "simulation only" Model, supported in
ARC ISS (Instruction Set Simulator).
The SMP extensions include:
-IDU (Interrupt Distribution Unit)
-XTL (To enable CPU start/stop/set-PC for another CPU)
It doesn't provide coherent Caches and/or Atomic Ops (LLOCK/SCOND)
config ARC_SERIAL_BAUD
int "UART Baud rate"
default "115200"
depends on SERIAL_ARC || SERIAL_ARC_CONSOLE
help
Baud rate for the ARC UART
menuconfig ARC_HAS_BVCI_LAT_UNIT
bool "BVCI Bus Latency Unit"
depends on ARC_BOARD_ML509 || ARC_BOARD_ANGEL4
help
IP to add artificial latency to BVCI Bus Based FPGA builds.
The default latency (even worst case) for FPGA is non-realistic
(~10 SDRAM, ~5 SSRAM).
config BVCI_LAT_UNITS
hex "Latency Unit(s) Bitmap"
default "0x0"
depends on ARC_HAS_BVCI_LAT_UNIT
help
There are multiple Latency Units corresponding to the many
interfaces of the system bus arbiter (both CPU side as well as
the peripheral side).
To add latency to ALL memory transaction, choose Unit 0, otherwise
for finer grainer - interface wise latency, specify a bitmap (1 bit
per unit) of all units. e.g. 1,2,12 will be 0x1003
Unit 0 - System Arb and Mem Controller
Unit 1 - I$ and System Bus
Unit 2 - D$ and System Bus
..
Unit 12 - IDE Disk controller and System Bus
config BVCI_LAT_CYCLES
int "Latency Value in cycles"
range 0 63
default "30"
depends on ARC_HAS_BVCI_LAT_UNIT
endif
|