5113f6f70
 김현기
kernel add
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
|
#ifndef _SPARC64_BACKOFF_H
#define _SPARC64_BACKOFF_H
/* The macros in this file implement an exponential backoff facility
* for atomic operations.
*
* When multiple threads compete on an atomic operation, it is
* possible for one thread to be continually denied a successful
* completion of the compare-and-swap instruction. Heavily
* threaded cpu implementations like Niagara can compound this
* problem even further.
*
* When an atomic operation fails and needs to be retried, we spin a
* certain number of times. At each subsequent failure of the same
* operation we double the spin count, realizing an exponential
* backoff.
*
* When we spin, we try to use an operation that will cause the
* current cpu strand to block, and therefore make the core fully
* available to any other other runnable strands. There are two
* options, based upon cpu capabilities.
*
* On all cpus prior to SPARC-T4 we do three dummy reads of the
* condition code register. Each read blocks the strand for something
* between 40 and 50 cpu cycles.
*
* For SPARC-T4 and later we have a special "pause" instruction
* available. This is implemented using writes to register %asr27.
* The cpu will block the number of cycles written into the register,
* unless a disrupting trap happens first. SPARC-T4 specifically
* implements pause with a granularity of 8 cycles. Each strand has
* an internal pause counter which decrements every 8 cycles. So the
* chip shifts the %asr27 value down by 3 bits, and writes the result
* into the pause counter. If a value smaller than 8 is written, the
* chip blocks for 1 cycle.
*
* To achieve the same amount of backoff as the three %ccr reads give
* on earlier chips, we shift the backoff value up by 7 bits. (Three
* %ccr reads block for about 128 cycles, 1 << 7 == 128) We write the
* whole amount we want to block into the pause register, rather than
* loop writing 128 each time.
*/
#define BACKOFF_LIMIT (4 * 1024)
#ifdef CONFIG_SMP
#define BACKOFF_SETUP(reg) \
mov 1, reg
#define BACKOFF_LABEL(spin_label, continue_label) \
spin_label
#define BACKOFF_SPIN(reg, tmp, label) \
mov reg, tmp; \
88: rd %ccr, %g0; \
rd %ccr, %g0; \
rd %ccr, %g0; \
.section .pause_3insn_patch,"ax";\
.word 88b; \
sllx tmp, 7, tmp; \
wr tmp, 0, %asr27; \
clr tmp; \
.previous; \
brnz,pt tmp, 88b; \
sub tmp, 1, tmp; \
set BACKOFF_LIMIT, tmp; \
cmp reg, tmp; \
bg,pn %xcc, label; \
nop; \
ba,pt %xcc, label; \
sllx reg, 1, reg;
#else
#define BACKOFF_SETUP(reg)
#define BACKOFF_LABEL(spin_label, continue_label) \
continue_label
#define BACKOFF_SPIN(reg, tmp, label)
#endif
#endif /* _SPARC64_BACKOFF_H */
|