/*
   * (C) Copyright 2003
   * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   *
   * SPDX-License-Identifier:	GPL-2.0+
   */
  
  /*
   * This file contains the configuration parameters for the dbau1x00 board.
   */
  
  #ifndef __CONFIG_H
  #define __CONFIG_H
  
  #define CONFIG_PB1X00		1
  #define CONFIG_SOC_AU1X00	1  /* alchemy series cpu */
  
  #define CONFIG_DISPLAY_BOARDINFO
  
  #ifdef CONFIG_PB1000
  #define CONFIG_SOC_AU1000	1
  #else
  #ifdef CONFIG_PB1100
  #define CONFIG_SOC_AU1100	1
  #else
  #ifdef CONFIG_PB1500
  #define CONFIG_SOC_AU1500	1
  #else
  #error "No valid board set"
  #endif
  #endif
  #endif
  
  #define CONFIG_ETHADDR		DE:AD:BE:EF:01:01    /* Ethernet address */
  
  #define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds	*/
  
  #define CONFIG_BAUDRATE		115200
  
  #define	CONFIG_TIMESTAMP		/* Print image info with timestamp */
  #undef	CONFIG_BOOTARGS
  
  #define	CONFIG_EXTRA_ENV_SETTINGS					\
  	"addmisc=setenv bootargs ${bootargs} "				\
  		"console=ttyS0,${baudrate} "				\
  		"panic=1\0"						\
  	"bootfile=/vmlinux.img\0"				\
  	"load=tftp 80500000 ${u-boot}\0"				\
  	""
  /* Boot from NFS root */
  #define CONFIG_BOOTCOMMAND	"bootp; setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm"
  
  /*
   * Miscellaneous configurable options
   */
  #define	CONFIG_SYS_LONGHELP				/* undef to save memory      */
  #define	CONFIG_SYS_PROMPT		"Pb1x00 # "	/* Monitor Command Prompt    */
  #define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size   */
  #define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)  /* Print Buffer Size */
  #define	CONFIG_SYS_MAXARGS		16		/* max number of command args*/
  
  #define CONFIG_SYS_MALLOC_LEN		128*1024
  
  #define CONFIG_SYS_BOOTPARAMS_LEN	128*1024
  
  #define CONFIG_SYS_MIPS_TIMER_FREQ	396000000
  
  #define CONFIG_SYS_SDRAM_BASE		0x80000000     /* Cached addr */
  
  #define	CONFIG_SYS_LOAD_ADDR		0x81000000     /* default load address	*/
  
  #define CONFIG_SYS_MEMTEST_START	0x80100000
  #undef CONFIG_SYS_MEMTEST_START
  #define CONFIG_SYS_MEMTEST_START       0x80200000
  #define CONFIG_SYS_MEMTEST_END		0x83800000
  
  /*-----------------------------------------------------------------------
   * FLASH and environment organization
   */
  #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
  #define CONFIG_SYS_MAX_FLASH_SECT	(128)	/* max number of sectors on one chip */
  
  #define PHYS_FLASH_1		0xbec00000 /* Flash Bank #1 */
  #define PHYS_FLASH_2		0xbfc00000 /* Flash Bank #2 */
  
  /* The following #defines are needed to get flash environment right */
  #define	CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
  #define	CONFIG_SYS_MONITOR_LEN		(192 << 10)
  
  #define CONFIG_SYS_INIT_SP_OFFSET	0x4000000
  
  /* We boot from this flash, selected with dip switch */
  #define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_2
  
  /* timeout values are in ticks */
  #define CONFIG_SYS_FLASH_ERASE_TOUT	(2 * CONFIG_SYS_HZ) /* Timeout for Flash Erase */
  #define CONFIG_SYS_FLASH_WRITE_TOUT	(2 * CONFIG_SYS_HZ) /* Timeout for Flash Write */
  
  #define	CONFIG_ENV_IS_NOWHERE	1
  
  /* Address and size of Primary Environment Sector	*/
  #define CONFIG_ENV_ADDR		0xB0030000
  #define CONFIG_ENV_SIZE		0x10000
  
  #define CONFIG_FLASH_16BIT
  
  #define CONFIG_NR_DRAM_BANKS	2
  
  
  #define CONFIG_MEMSIZE_IN_BYTES
  
  
  /*---USB -------------------------------------------*/
  #if 0
  #define CONFIG_USB_OHCI
  #define CONFIG_USB_STORAGE
  #define CONFIG_DOS_PARTITION
  #endif
  
  /*---ATA PCMCIA ------------------------------------*/
  #if 0
  #define CONFIG_SYS_PCMCIA_MEM_SIZE 0x4000000 /* Offset to slot 1 FIXME!!! */
  #define CONFIG_SYS_PCMCIA_MEM_ADDR 0x20000000
  #define CONFIG_PCMCIA_SLOT_A
  
  #define CONFIG_ATAPI 1
  #define CONFIG_MAC_PARTITION 1
  
  /* We run CF in "true ide" mode or a harddrive via pcmcia */
  #define CONFIG_IDE_PCMCIA 1
  
  /* We only support one slot for now */
  #define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
  #define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
  
  #undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
  #undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
  
  #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
  
  #define CONFIG_SYS_ATA_BASE_ADDR       CONFIG_SYS_PCMCIA_MEM_ADDR
  
  /* Offset for data I/O			*/
  #define CONFIG_SYS_ATA_DATA_OFFSET     8
  
  /* Offset for normal register accesses  */
  #define CONFIG_SYS_ATA_REG_OFFSET      0
  
  /* Offset for alternate registers       */
  #define CONFIG_SYS_ATA_ALT_OFFSET      0x0100
  
  #endif
  /*-----------------------------------------------------------------------
   * Cache Configuration
   */
  #define CONFIG_SYS_DCACHE_SIZE		16384
  #define CONFIG_SYS_ICACHE_SIZE		16384
  #define CONFIG_SYS_CACHELINE_SIZE	32
  
  
  /*
   * BOOTP options
   */
  #define CONFIG_BOOTP_BOOTFILESIZE
  #define CONFIG_BOOTP_BOOTPATH
  #define CONFIG_BOOTP_GATEWAY
  #define CONFIG_BOOTP_HOSTNAME
  
  
  /*
   * Command line configuration.
   */
  #include <config_cmd_default.h>
  
  #define CONFIG_CMD_DHCP
  #define CONFIG_CMD_ELF
  #define CONFIG_CMD_MII
  #define CONFIG_CMD_PING
  
  #undef CONFIG_CMD_SAVEENV
  #undef CONFIG_CMD_FAT
  #undef CONFIG_CMD_FLASH
  #undef CONFIG_CMD_FPGA
  #undef CONFIG_CMD_IDE
  #undef CONFIG_CMD_LOADS
  #undef CONFIG_CMD_RUN
  #undef CONFIG_CMD_LOADB
  #undef CONFIG_CMD_ELF
  #undef CONFIG_CMD_BDI
  #undef CONFIG_CMD_BEDBUG
  
  #endif	/* __CONFIG_H */