/*
   * (C) Copyright 2003-2007
   * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   *
   * SPDX-License-Identifier:	GPL-2.0+
   */
  
  #ifndef __CONFIG_H
  #define __CONFIG_H
  
  
  #define CONFIG_SYS_GENERIC_BOARD
  #define CONFIG_DISPLAY_BOARDINFO
  
  
  /*
   * High Level Configuration Options
   */
  #define CONFIG_MPC5200		1	/* This is an MPC5200 CPU */
  #define CONFIG_CM5200		1	/* ... on CM5200 platform */
  
  #define	CONFIG_SYS_TEXT_BASE	0xfc000000
  
  #define CONFIG_HIGH_BATS	1	/* High BATs supported */
  
  /*
   * Supported commands
   */
  #include <config_cmd_default.h>
  
  #define CONFIG_CMD_ASKENV
  #define CONFIG_CMD_BSP
  #define CONFIG_CMD_DATE
  #define CONFIG_CMD_DHCP
  #define CONFIG_CMD_DIAG
  #define CONFIG_CMD_FAT
  #define CONFIG_CMD_I2C
  #define CONFIG_CMD_JFFS2
  #define CONFIG_CMD_MII
  #define CONFIG_CMD_NFS
  #define CONFIG_CMD_PING
  #define CONFIG_CMD_REGINFO
  #define CONFIG_CMD_SNTP
  #define CONFIG_CMD_USB
  
  /*
   * Serial console configuration
   */
  #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
  #define CONFIG_BAUDRATE		57600	/* ... at 57600 bps */
  #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
  #define CONFIG_SILENT_CONSOLE	1	/* needed to silence i2c_init() */
  
  /*
   * Ethernet configuration
   */
  #define CONFIG_MPC5xxx_FEC	1
  #define CONFIG_MPC5xxx_FEC_MII100
  #define CONFIG_PHY_ADDR		0x00
  #define CONFIG_ENV_OVERWRITE	1	/* allow overwriting of ethaddr */
  /* use misc_init_r() to read ethaddr from I2C EEPROM (see CONFIG_SYS_I2C_EEPROM) */
  #define CONFIG_MISC_INIT_R	1
  #define CONFIG_MAC_OFFSET	0x35	/* MAC address offset in I2C EEPROM */
  
  /*
   * POST support
   */
  #define CONFIG_POST		(CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
  #define MPC5XXX_SRAM_POST_SIZE	(MPC5XXX_SRAM_SIZE - 4)
  /* List of I2C addresses to be verified by POST */
  #define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_SLAVE,	\
  					 CONFIG_SYS_I2C_IO,	\
  					 CONFIG_SYS_I2C_EEPROM}
  
  /* display image timestamps */
  #define CONFIG_TIMESTAMP	1
  
  /*
   * Autobooting
   */
  #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
  #define CONFIG_PREBOOT	"echo;" \
  	"echo Type \"run net_nfs_fdt\" to mount root filesystem over NFS;" \
  	"echo"
  #undef CONFIG_BOOTARGS
  
  /*
   * Default environment settings
   */
  #define CONFIG_EXTRA_ENV_SETTINGS					\
  	"netdev=eth0\0"							\
  	"netmask=255.255.0.0\0"						\
  	"ipaddr=192.168.160.33\0"					\
  	"serverip=192.168.1.1\0"					\
  	"gatewayip=192.168.1.1\0"					\
  	"console=ttyPSC0\0"						\
  	"u-boot_addr=100000\0"						\
  	"kernel_addr=200000\0"						\
  	"kernel_addr_flash=fc0c0000\0"					\
  	"fdt_addr=400000\0"						\
  	"fdt_addr_flash=fc0a0000\0"					\
  	"ramdisk_addr=500000\0"						\
  	"rootpath=/opt/eldk-4.1/ppc_6xx\0"				\
  	"u-boot=/tftpboot/cm5200/u-boot.bin\0"				\
  	"bootfile_fdt=/tftpboot/cm5200/uImage\0"			\
  	"fdt_file=/tftpboot/cm5200/cm5200.dtb\0"			\
  	"load=tftp ${u-boot_addr} ${u-boot}\0"				\
  	"update=prot off fc000000 +${filesize}; "			\
  		"era fc000000 +${filesize}; "				\
  		"cp.b ${u-boot_addr} fc000000 ${filesize}; "		\
  		"prot on fc000000 +${filesize}\0"			\
  	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
  		"nfsroot=${serverip}:${rootpath}\0"			\
  	"flashargs=setenv bootargs root=/dev/mtdblock5 rw\0"		\
  	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
  	"addinit=setenv bootargs ${bootargs} init=/linuxrc\0"		\
  	"addcons=setenv bootargs ${bootargs} "				\
  		"console=${console},${baudrate}\0"			\
  	"addip=setenv bootargs ${bootargs} "				\
  		"ip=${ipaddr}:${serverip}:${gatewayip}:"		\
  		"${netmask}:${hostname}:${netdev}:off panic=1\0"	\
  	"flash_flash=run flashargs addinit addip addcons;"		\
  		"bootm ${kernel_addr_flash} - ${fdt_addr_flash}\0"	\
  	"net_nfs_fdt=tftp ${kernel_addr} ${bootfile_fdt}; "		\
  		"tftp ${fdt_addr} ${fdt_file}; run nfsargs addip "	\
  		"addcons; bootm ${kernel_addr} - ${fdt_addr}\0"		\
  	""
  #define CONFIG_BOOTCOMMAND	"run flash_flash"
  
  /*
   * Low level configuration
   */
  
  /*
   * Clock configuration
   */
  #define CONFIG_SYS_MPC5XXX_CLKIN	33000000	/* SYS_XTAL_IN = 33MHz */
  #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK	1	/* IPB = 133MHz */
  
  /*
   * Memory map
   */
  #define CONFIG_SYS_MBAR		0xF0000000
  #define CONFIG_SYS_SDRAM_BASE		0x00000000
  #define CONFIG_SYS_DEFAULT_MBAR	0x80000000
  
  #define CONFIG_SYS_LOWBOOT		1
  
  /* Use ON-Chip SRAM until RAM will be available */
  #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
  #ifdef CONFIG_POST
  /* preserve space for the post_word at end of on-chip SRAM */
  #define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_POST_SIZE
  #else
  #define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE
  #endif
  
  #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
  #define CONFIG_BOARD_TYPES	1	/* we use board_type */
  
  #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
  
  #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
  #define CONFIG_SYS_MONITOR_LEN		(384 << 10)	/* 384 kB for Monitor */
  #define CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* 256 kB for malloc() */
  #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* initial mem map for Linux */
  
  /*
   * Flash configuration
   */
  #define CONFIG_SYS_FLASH_CFI		1
  #define CONFIG_FLASH_CFI_DRIVER	1
  #define CONFIG_SYS_FLASH_BASE		0xfc000000
  /* we need these despite using CFI */
  #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks */
  #define CONFIG_SYS_MAX_FLASH_SECT	256	/* max num of sectors on one chip */
  #define CONFIG_SYS_FLASH_SIZE		0x02000000 /* 32 MiB */
  
  
  #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
  #define CONFIG_SYS_RAMBOOT		1
  #undef CONFIG_SYS_LOWBOOT
  #endif
  
  
  /*
   * Chip selects configuration
   */
  /* Boot Chipselect */
  #define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
  #define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
  #define CONFIG_SYS_BOOTCS_CFG		0x00087D31	/* for pci_clk = 33 MHz */
  /* use board_early_init_r to enable flash write in CS_BOOT */
  #define CONFIG_BOARD_EARLY_INIT_R
  
  /* Flash memory addressing */
  #define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
  #define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
  
  /* No burst, dead cycle = 1 for CS0 (Flash) */
  #define CONFIG_SYS_CS_BURST		0x00000000
  #define CONFIG_SYS_CS_DEADCYCLE	0x00000001
  
  /*
   * SDRAM configuration
   * settings for k4s561632E-xx75, assuming XLB = 132 MHz
   */
  #define SDRAM_MODE	0x00CD0000	/* CASL 3, burst length 8 */
  #define SDRAM_CONTROL	0x514F0000
  #define SDRAM_CONFIG1	0xE2333900
  #define SDRAM_CONFIG2	0x8EE70000
  
  /*
   * MTD configuration
   */
  #define CONFIG_CMD_MTDPARTS	1
  #define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
  #define CONFIG_FLASH_CFI_MTD
  #define MTDIDS_DEFAULT		"nor0=cm5200-0"
  #define MTDPARTS_DEFAULT	"mtdparts=cm5200-0:"			\
  					"384k(uboot),128k(env),"	\
  					"128k(redund_env),128k(dtb),"	\
  					"2m(kernel),27904k(rootfs),"	\
  					"-(config)"
  
  /*
   * I2C configuration
   */
  #define CONFIG_HARD_I2C		1	/* I2C with hardware support */
  #define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #2 */
  #define CONFIG_SYS_I2C_SPEED		40000	/* 40 kHz */
  #define CONFIG_SYS_I2C_SLAVE		0x0
  #define CONFIG_SYS_I2C_IO		0x38	/* PCA9554AD I2C I/O port address */
  #define CONFIG_SYS_I2C_EEPROM		0x53	/* I2C EEPROM device address */
  
  /*
   * RTC configuration
   */
  #define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */
  
  /*
   * USB configuration
   */
  #define CONFIG_USB_OHCI		1
  #define CONFIG_USB_STORAGE	1
  #define CONFIG_USB_CLOCK	0x0001BBBB
  #define CONFIG_USB_CONFIG	0x00001000
  /* Partitions (for USB) */
  #define CONFIG_MAC_PARTITION	1
  #define CONFIG_DOS_PARTITION	1
  #define CONFIG_ISO_PARTITION	1
  
  /*
   * Invoke our last_stage_init function - needed by fwupdate
   */
  #define CONFIG_LAST_STAGE_INIT	1
  
  /*
   * Environment settings
   */
  #define CONFIG_ENV_IS_IN_FLASH	1
  #define CONFIG_ENV_SIZE		0x10000
  #define CONFIG_ENV_SECT_SIZE	0x20000
  #define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
  /* Configuration of redundant environment */
  #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
  #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
  
  /*
   * Pin multiplexing configuration
   */
  
  /*
   * CS1/GPIO_WKUP_6: GPIO (default)
   * ALTs: CAN1 on I2C1, CAN2 on TIMER0/1
   * IRDA/PSC6: UART
   * Ether: Ethernet 100Mbit with MD
   * PCI_DIS: PCI controller disabled
   * USB: USB
   * PSC3: SPI with UART3
   * PSC2: UART
   * PSC1: UART
   */
  #define CONFIG_SYS_GPS_PORT_CONFIG	0x10559C44
  
  /*
   * Miscellaneous configurable options
   */
  #define CONFIG_SYS_LONGHELP		1	/* undef to save memory */
  #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
  #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
  #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
  #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
  
  #define CONFIG_SYS_ALT_MEMTEST		1
  #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
  #define CONFIG_SYS_MEMTEST_END		0x03f00000	/* 1 .. 63 MiB in SDRAM */
  
  #define CONFIG_LOOPW		1
  
  #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
  
  /*
   * Various low-level settings
   */
  #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
  #define CONFIG_SYS_HID0_FINAL		HID0_ICE
  
  #define CONFIG_SYS_XLB_PIPELINING	1	/* enable transaction pipeling */
  
  /*
   * Cache Configuration
   */
  #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
  #ifdef CONFIG_CMD_KGDB
  #define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
  #endif
  
  /*
   * Flat Device Tree support
   */
  #define CONFIG_OF_LIBFDT	1
  #define CONFIG_OF_BOARD_SETUP	1
  #define OF_CPU			"PowerPC,5200@0"
  #define OF_SOC			"soc5200@f0000000"
  #define OF_TBCLK		(bd->bi_busfreq / 4)
  #define OF_STDOUT_PATH		"/soc5200@f0000000/serial@2000"
  
  #endif /* __CONFIG_H */