6b13f685e
 김민수
BSP 최초 추가
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
|
/*
* (C) Copyright 2003
* Thomas.Lange@corelatus.se
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <command.h>
#include <asm/au1x00.h>
#include <asm/mipsregs.h>
#include <asm/io.h>
phys_size_t initdram(int board_type)
{
/* Sdram is setup by assembler code */
/* If memory could be changed, we should return the true value here */
return MEM_SIZE*1024*1024;
}
#define BCSR_PCMCIA_PC0DRVEN 0x0010
#define BCSR_PCMCIA_PC0RST 0x0080
/* In arch/mips/cpu/cpu.c */
void write_one_tlb( int index, u32 pagemask, u32 hi, u32 low0, u32 low1 );
int checkboard (void)
{
#ifdef CONFIG_IDE_PCMCIA
u16 status;
volatile u32 *pcmcia_bcsr = (u32*)(DB1XX0_BCSR_ADDR+0x10);
#endif /* CONFIG_IDE_PCMCIA */
volatile u32 *phy = (u32*)(DB1XX0_BCSR_ADDR+0xC);
volatile u32 *sys_counter = (volatile u32*)SYS_COUNTER_CNTRL;
u32 proc_id;
*sys_counter = 0x100; /* Enable 32 kHz oscillator for RTC/TOY */
proc_id = read_c0_prid();
switch (proc_id >> 24) {
case 0:
puts ("Board: Merlot (DbAu1000)
");
printf ("CPU: Au1000 396 MHz, id: 0x%02x, rev: 0x%02x
",
(proc_id >> 8) & 0xFF, proc_id & 0xFF);
break;
case 1:
puts ("Board: DbAu1500
");
printf ("CPU: Au1500, id: 0x%02x, rev: 0x%02x
",
(proc_id >> 8) & 0xFF, proc_id & 0xFF);
break;
case 2:
puts ("Board: DbAu1100
");
printf ("CPU: Au1100, id: 0x%02x, rev: 0x%02x
",
(proc_id >> 8) & 0xFF, proc_id & 0xFF);
break;
case 3:
puts ("Board: DbAu1550
");
printf ("CPU: Au1550, id: 0x%02x, rev: 0x%02x
",
(proc_id >> 8) & 0xFF, proc_id & 0xFF);
break;
default:
printf ("Unsupported cpu %d, proc_id=0x%x
", proc_id >> 24, proc_id);
}
set_io_port_base(0);
#ifdef CONFIG_IDE_PCMCIA
/* Enable 3.3 V on slot 0 ( VCC )
No 5V */
status = 4;
*pcmcia_bcsr = status;
status |= BCSR_PCMCIA_PC0DRVEN;
*pcmcia_bcsr = status;
au_sync();
udelay(300*1000);
status |= BCSR_PCMCIA_PC0RST;
*pcmcia_bcsr = status;
au_sync();
udelay(100*1000);
/* PCMCIA is on a 36 bit physical address.
We need to map it into a 32 bit addresses */
#if 0
/* We dont need theese unless we run whole pcmcia package */
write_one_tlb(20, /* index */
0x01ffe000, /* Pagemask, 16 MB pages */
CONFIG_SYS_PCMCIA_IO_BASE, /* Hi */
0x3C000017, /* Lo0 */
0x3C200017); /* Lo1 */
write_one_tlb(21, /* index */
0x01ffe000, /* Pagemask, 16 MB pages */
CONFIG_SYS_PCMCIA_ATTR_BASE, /* Hi */
0x3D000017, /* Lo0 */
0x3D200017); /* Lo1 */
#endif /* 0 */
write_one_tlb(22, /* index */
0x01ffe000, /* Pagemask, 16 MB pages */
CONFIG_SYS_PCMCIA_MEM_ADDR, /* Hi */
0x3E000017, /* Lo0 */
0x3E200017); /* Lo1 */
#endif /* CONFIG_IDE_PCMCIA */
/* Release reset of ethernet PHY chips */
/* Always do this, because linux does not know about it */
*phy = 3;
return 0;
}
|