6b13f685e
 김민수
BSP 최초 추가
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
|
What: /sys/class/ata_...
Date: August 2008
Contact: Gwendal Grignou<gwendal@google.com>
Description:
Provide a place in sysfs for storing the ATA topology of the system. This allows
retrieving various information about ATA objects.
Files under /sys/class/ata_port
-------------------------------
For each port, a directory ataX is created where X is the ata_port_id of
the port. The device parent is the ata host device.
idle_irq (read)
Number of IRQ received by the port while idle [some ata HBA only].
nr_pmp_links (read)
If a SATA Port Multiplier (PM) is connected, number of link behind it.
Files under /sys/class/ata_link
-------------------------------
Behind each port, there is a ata_link. If there is a SATA PM in the
topology, 15 ata_link objects are created.
If a link is behind a port, the directory name is linkX, where X is
ata_port_id of the port.
If a link is behind a PM, its name is linkX.Y where X is ata_port_id
of the parent port and Y the PM port.
hw_sata_spd_limit
Maximum speed supported by the connected SATA device.
sata_spd_limit
Maximum speed imposed by libata.
sata_spd
Current speed of the link [1.5, 3Gps,...].
Files under /sys/class/ata_device
---------------------------------
Behind each link, up to two ata device are created.
The name of the directory is devX[.Y].Z where:
- X is ata_port_id of the port where the device is connected,
- Y the port of the PM if any, and
- Z the device id: for PATA, there is usually 2 devices [0,1],
only 1 for SATA.
class
Device class. Can be "ata" for disk, "atapi" for packet device,
"pmp" for PM, or "none" if no device was found behind the link.
dma_mode
Transfer modes supported by the device when in DMA mode.
Mostly used by PATA device.
pio_mode
Transfer modes supported by the device when in PIO mode.
Mostly used by PATA device.
xfer_mode
Current transfer mode.
id
Cached result of IDENTIFY command, as described in ATA8 7.16 and 7.17.
Only valid if the device is not a PM.
gscr
Cached result of the dump of PM GSCR register.
Valid registers are:
0: SATA_PMP_GSCR_PROD_ID,
1: SATA_PMP_GSCR_REV,
2: SATA_PMP_GSCR_PORT_INFO,
32: SATA_PMP_GSCR_ERROR,
33: SATA_PMP_GSCR_ERROR_EN,
64: SATA_PMP_GSCR_FEAT,
96: SATA_PMP_GSCR_FEAT_EN,
130: SATA_PMP_GSCR_SII_GPIO
Only valid if the device is a PM.
spdn_cnt
Number of time libata decided to lower the speed of link due to errors.
ering
Formatted output of the error ring of the device.
|