Blame view

bootloader/u-boot_2015_04/include/configs/draco.h 1.95 KB
6b13f685e   김민수   BSP 최초 추가
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
  /*
   * (C) Copyright 2013 Siemens Schweiz AG
   * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
   *
   * Based on:
   * U-Boot file:/include/configs/am335x_evm.h
   *
   * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
   *
   * SPDX-License-Identifier:	GPL-2.0+
   */
  
  #ifndef __CONFIG_DRACO_H
  #define __CONFIG_DRACO_H
  
  #define CONFIG_SIEMENS_DRACO
  #define MACH_TYPE_DRACO			4314
  #define CONFIG_SIEMENS_MACH_TYPE	MACH_TYPE_DRACO
  
  #include "siemens-am33x-common.h"
  
  #define CONFIG_SYS_MPUCLK	275
  #define DDR_PLL_FREQ	303
  #undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
  
  #define BOARD_DFU_BUTTON_GPIO	27
  #define BOARD_DFU_BUTTON_LED	64	/* red LED */
  #define BOARD_STATUS_LED	103	/* green LED */
  #define GPIO_LAN9303_NRST	88	/* GPIO2_24 = gpio88 */
  
  #undef CONFIG_DOS_PARTITION
  #undef CONFIG_CMD_FAT
  
  
   /* Physical Memory Map */
  #define CONFIG_MAX_RAM_BANK_SIZE	(1024 << 20)	/* 1GB */
  
  /* I2C Configuration */
  #define CONFIG_SYS_I2C_SPEED		100000
  
  #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
  #define EEPROM_ADDR_DDR3 0x90
  #define EEPROM_ADDR_CHIP 0x120
  
  #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x300
  
  #undef CONFIG_SPL_NET_SUPPORT
  #undef CONFIG_SPL_NET_VCI_STRING
  #undef CONFIG_SPL_ETH_SUPPORT
  
  #undef CONFIG_MII
  #undef CONFIG_PHY_GIGE
  #define CONFIG_PHY_SMSC
  
  #define CONFIG_FACTORYSET
  
  /* Watchdog */
  #define CONFIG_OMAP_WATCHDOG
  
  #ifndef CONFIG_SPL_BUILD
  
  /* Default env settings */
  #define CONFIG_EXTRA_ENV_SETTINGS \
  	"nand_img_size=0x400000\0" \
  	"optargs=\0" \
  	CONFIG_COMMON_ENV_SETTINGS
  
  #ifndef CONFIG_RESTORE_FLASH
  /* set to negative value for no autoboot */
  #define CONFIG_BOOTDELAY		3
  
  #define CONFIG_BOOTCOMMAND \
  "if dfubutton; then " \
  	"run dfu_start; " \
  	"reset; " \
  "fi;" \
  "run nand_boot;" \
  "reset;"
  
  
  #else
  #define CONFIG_BOOTDELAY		0
  
  #define CONFIG_BOOTCOMMAND			\
  	"setenv autoload no; "			\
  	"dhcp; "				\
  	"if tftp 80000000 debrick.scr; then "	\
  		"source 80000000; "		\
  	"fi"
  #endif
  #endif	/* CONFIG_SPL_BUILD */
  #endif	/* ! __CONFIG_DRACO_H */