6b13f685e
 김민수
BSP 최초 추가
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
|
/*
* Copyright (C) 1996 Linus Torvalds & author (see below)
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/timer.h>
#include <linux/mm.h>
#include <linux/ioport.h>
#include <linux/blkdev.h>
#include <linux/ide.h>
#include <linux/init.h>
#include <asm/io.h>
#define DRV_NAME "dtc2278"
/*
* Changing this #undef to #define may solve start up problems in some systems.
*/
#undef ALWAYS_SET_DTC2278_PIO_MODE
/*
* From: andy@cercle.cts.com (Dyan Wile)
*
* Below is a patch for DTC-2278 - alike software-programmable controllers
* The code enables the secondary IDE controller and the PIO4 (3?) timings on
* the primary (EIDE). You may probably have to enable the 32-bit support to
* get the full speed. You better get the disk interrupts disabled ( hdparm -u0
* /dev/hd.. ) for the drives connected to the EIDE interface. (I get my
* filesystem corrupted with -u1, but under heavy disk load only :-)
*
* This card is now forced to use the "serialize" feature,
* and irq-unmasking is disallowed. If io_32bit is enabled,
* it must be done for BOTH drives on each interface.
*
* This code was written for the DTC2278E, but might work with any of these:
*
* DTC2278S has only a single IDE interface.
* DTC2278D has two IDE interfaces and is otherwise identical to the S version.
* DTC2278E also has serial ports and a printer port
* DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford <kent@theory.caltech.edu>
*
* There may be a fourth controller type. The S and D versions use the
* Winbond chip, and I think the E version does also.
*
*/
static void sub22 (char b, char c)
{
int i;
for(i = 0; i < 3; ++i) {
inb(0x3f6);
outb_p(b,0xb0);
inb(0x3f6);
outb_p(c,0xb4);
inb(0x3f6);
if(inb(0xb4) == c) {
outb_p(7,0xb0);
inb(0x3f6);
return; /* success */
}
}
}
static DEFINE_SPINLOCK(dtc2278_lock);
static void dtc2278_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
unsigned long flags;
if (drive->pio_mode >= XFER_PIO_3) {
spin_lock_irqsave(&dtc2278_lock, flags);
/*
* This enables PIO mode4 (3?) on the first interface
*/
sub22(1,0xc3);
sub22(0,0xa0);
spin_unlock_irqrestore(&dtc2278_lock, flags);
} else {
/* we don't know how to set it back again.. */
/* Actually we do - there is a data sheet available for the
Winbond but does anyone actually care */
}
}
static const struct ide_port_ops dtc2278_port_ops = {
.set_pio_mode = dtc2278_set_pio_mode,
};
static const struct ide_port_info dtc2278_port_info __initconst = {
.name = DRV_NAME,
.chipset = ide_dtc2278,
.port_ops = &dtc2278_port_ops,
.host_flags = IDE_HFLAG_SERIALIZE |
IDE_HFLAG_NO_UNMASK_IRQS |
IDE_HFLAG_IO_32BIT |
/* disallow ->io_32bit changes */
IDE_HFLAG_NO_IO_32BIT |
IDE_HFLAG_NO_DMA |
IDE_HFLAG_DTC2278,
.pio_mask = ATA_PIO4,
};
static int __init dtc2278_probe(void)
{
unsigned long flags;
local_irq_save(flags);
/*
* This enables the second interface
*/
outb_p(4,0xb0);
inb(0x3f6);
outb_p(0x20,0xb4);
inb(0x3f6);
#ifdef ALWAYS_SET_DTC2278_PIO_MODE
/*
* This enables PIO mode4 (3?) on the first interface
* and may solve start-up problems for some people.
*/
sub22(1,0xc3);
sub22(0,0xa0);
#endif
local_irq_restore(flags);
return ide_legacy_device_add(&dtc2278_port_info, 0);
}
static bool probe_dtc2278;
module_param_named(probe, probe_dtc2278, bool, 0);
MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets");
static int __init dtc2278_init(void)
{
if (probe_dtc2278 == 0)
return -ENODEV;
if (dtc2278_probe()) {
printk(KERN_ERR "dtc2278: ide interfaces already in use!
");
return -EBUSY;
}
return 0;
}
module_init(dtc2278_init);
MODULE_AUTHOR("See Local File");
MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets");
MODULE_LICENSE("GPL");
|