#!/bin/sh
  #
  # test types can be passed on the command line:
  #
  # - control: any device can do this
  # - out, in:  out needs 'bulk sink' firmware, in needs 'bulk src'
  # - iso-out, iso-in:  out needs 'iso sink' firmware, in needs 'iso src'
  # - halt: needs bulk sink+src, tests halt set/clear from host
  # - unlink: needs bulk sink and/or src, test HCD unlink processing
  # - loop: needs firmware that will buffer N transfers
  #
  # run it for hours, days, weeks.
  #
  
  #
  # this default provides a steady test load for a bulk device
  #
  TYPES='control out in'
  #TYPES='control out in halt'
  
  #
  # to test HCD code
  #
  #  - include unlink tests
  #  - add some ${RANDOM}ness
  #  - connect several devices concurrently (same HC)
  #  - keep HC's IRQ lines busy with unrelated traffic (IDE, net, ...)
  #  - add other concurrent system loads
  #
  
  declare -i COUNT BUFLEN
  
  COUNT=50000
  BUFLEN=2048
  
  # NOTE:  the 'in' and 'out' cases are usually bulk, but can be
  # set up to use interrupt transfers by 'usbtest' module options
  
  
  if [ "$DEVICE" = "" ]; then
  	echo "testing ALL recognized usbtest devices"
  	echo ""
  	TEST_ARGS="-a"
  else
  	TEST_ARGS=""
  fi
  
  do_test ()
  {
      if ! ./testusb $TEST_ARGS -s $BUFLEN -c $COUNT $* 2>/dev/null
      then
  	echo "FAIL"
  	exit 1
      fi
  }
  
  ARGS="$*"
  
  if [ "$ARGS" = "" ];
  then
      ARGS="$TYPES"
  fi
  
  # FIXME use /sys/bus/usb/device/$THIS/bConfigurationValue to
  # check and change configs
  
  CONFIG=''
  
  check_config ()
  {
      if [ "$CONFIG" = "" ]; then
  	CONFIG=$1
  	echo "assuming $CONFIG configuration"
  	return
      fi
      if [ "$CONFIG" = $1 ]; then
  	return
      fi
  
      echo "** device must be in $1 config, but it's $CONFIG instead"
      exit 1
  }
  
  
  echo "TESTING:  $ARGS"
  
  while : true
  do
      echo $(date)
  
      for TYPE in $ARGS
      do
  	# restore defaults
  	COUNT=5000
  	BUFLEN=2048
  
  	# FIXME automatically multiply COUNT by 10 when
  	# /sys/bus/usb/device/$THIS/speed == "480"
  
  #	COUNT=50000
  
  	case $TYPE in
  	control)
  	    # any device, in any configuration, can use this.
  	    echo '** Control test cases:'
  
  	    echo "test 9: ch9 postconfig"
  	    do_test -t 9 -c 5000
  	    echo "test 10: control queueing"
  	    do_test -t 10 -c 5000
  
  	    # this relies on some vendor-specific commands
  	    echo "test 14: control writes"
  	    do_test -t 14 -c 15000 -s 256 -v 1
  
  	    echo "test 21: control writes, unaligned"
  	    do_test -t 21 -c 100 -s 256 -v 1
  
  	    ;;
  
  	out)
  	    check_config sink-src
  	    echo '** Host Write (OUT) test cases:'
  
  	    echo "test 1: $COUNT transfers, same size"
  	    do_test -t 1
  	    echo "test 3: $COUNT transfers, variable/short size"
  	    do_test -t 3 -v 421
  
  	    COUNT=100
  	    echo "test 17: $COUNT transfers, unaligned DMA map by core"
  	    do_test -t 17
  
  	    echo "test 19: $COUNT transfers, unaligned DMA map by usb_alloc_coherent"
  	    do_test -t 19
  
  	    COUNT=2000
  	    echo "test 5: $COUNT scatterlists, same size entries"
  	    do_test -t 5
  
  	    # try to trigger short OUT processing bugs
  	    echo "test 7a: $COUNT scatterlists, variable size/short entries"
  	    do_test -t 7 -v 579
  	    BUFLEN=4096
  	    echo "test 7b: $COUNT scatterlists, variable size/bigger entries"
  	    do_test -t 7 -v 41
  	    BUFLEN=64
  	    echo "test 7c: $COUNT scatterlists, variable size/micro entries"
  	    do_test -t 7 -v 63
  	    ;;
  
  	iso-out)
  	    check_config sink-src
  	    echo '** Host ISOCHRONOUS Write (OUT) test cases:'
  
  	    # at peak iso transfer rates:
  	    # - usb 2.0 high bandwidth, this is one frame.
  	    # - usb 1.1, it's twenty-four frames.
  	    BUFLEN=24500
  
  	    COUNT=1000
  
  # COUNT=10000
  
  	    echo "test 15: $COUNT transfers, same size"
  	    # do_test -t 15 -g 3 -v 0
  	    BUFLEN=32768
  	    do_test -t 15 -g 8 -v 0
  
  	    # FIXME it'd make sense to have an iso OUT test issuing
  	    # short writes on more packets than the last one
  
  	    COUNT=100
  	    echo "test 22: $COUNT transfers, non aligned"
  	    do_test -t 22 -g 8 -v 0
  
  	    ;;
  
  	in)
  	    check_config sink-src
  	    echo '** Host Read (IN) test cases:'
  
  	    # NOTE:  these "variable size" reads are just multiples
  	    # of 512 bytes, no EOVERFLOW testing is done yet
  
  	    echo "test 2: $COUNT transfers, same size"
  	    do_test -t 2
  	    echo "test 4: $COUNT transfers, variable size"
  	    do_test -t 4
  
  	    COUNT=100
  	    echo "test 18: $COUNT transfers, unaligned DMA map by core"
  	    do_test -t 18
  
  	    echo "test 20: $COUNT transfers, unaligned DMA map by usb_alloc_coherent"
  	    do_test -t 20
  
  	    COUNT=2000
  	    echo "test 6: $COUNT scatterlists, same size entries"
  	    do_test -t 6
  	    echo "test 8: $COUNT scatterlists, variable size entries"
  	    do_test -t 8
  	    ;;
  
  	iso-in)
  	    check_config sink-src
  	    echo '** Host ISOCHRONOUS Read (IN) test cases:'
  
  	    # at peak iso transfer rates:
  	    # - usb 2.0 high bandwidth, this is one frame.
  	    # - usb 1.1, it's twenty-four frames.
  	    BUFLEN=24500
  
  	    COUNT=1000
  
  # COUNT=10000
  
  	    echo "test 16: $COUNT transfers, same size"
  	    # do_test -t 16 -g 3 -v 0
  	    BUFLEN=32768
  	    do_test -t 16 -g 8 -v 0
  
  	    # FIXME since iso expects faults, it'd make sense
  	    # to have an iso IN test issuing short reads ...
  
  	    COUNT=100
  	    echo "test 23: $COUNT transfers, unaligned"
  	    do_test -t 23 -g 8 -v 0
  
  	    ;;
  
  	halt)
  	    # NOTE:  sometimes hardware doesn't cooperate well with halting
  	    # endpoints from the host side.  so long as mass-storage class
  	    # firmware can halt them from the device, don't worry much if
  	    # you can't make this test work on your device.
  	    COUNT=2000
  	    echo "test 13: $COUNT halt set/clear"
  	    do_test -t 13
  	    ;;
  
  	unlink)
  	    COUNT=2000
  	    echo "test 11: $COUNT read unlinks"
  	    do_test -t 11
  
  	    echo "test 12: $COUNT write unlinks"
  	    do_test -t 12
  	    ;;
  
  	loop)
  	    # defaults need too much buffering for ez-usb devices
  	    BUFLEN=2048
  	    COUNT=32
  
  	    # modprobe g_zero qlen=$COUNT buflen=$BUFLEN loopdefault
  	    check_config loopback
  
  	    # FIXME someone needs to write and merge a version of this
  
  	    echo "write $COUNT buffers of $BUFLEN bytes, read them back"
  
  	    echo "write $COUNT variable size buffers, read them back"
  
  	    ;;
  
  	*)
  	    echo "Don't understand test type $TYPE"
  	    exit 1;
  	esac
  	echo ''
      done
  done
  
  # vim: sw=4