Blame view

kernel/linux-imx6_3.14.28/include/sound/wm8962.h 1.8 KB
6b13f685e   김민수   BSP 최초 추가
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
  /*
   * wm8962.h  --  WM8962 Soc Audio driver platform data
   *
   * This program is free software; you can redistribute it and/or modify
   * it under the terms of the GNU General Public License version 2 as
   * published by the Free Software Foundation.
   */
  
  #ifndef _WM8962_PDATA_H
  #define _WM8962_PDATA_H
  
  #define WM8962_MAX_GPIO 6
  
  /* Use to set GPIO default values to zero */
  #define WM8962_GPIO_SET 0x10000
  
  #define WM8962_GPIO_FN_CLKOUT           0
  #define WM8962_GPIO_FN_LOGIC            1
  #define WM8962_GPIO_FN_SDOUT            2
  #define WM8962_GPIO_FN_IRQ              3
  #define WM8962_GPIO_FN_THERMAL          4
  #define WM8962_GPIO_FN_PLL2_LOCK        6
  #define WM8962_GPIO_FN_PLL3_LOCK        7
  #define WM8962_GPIO_FN_FLL_LOCK         9
  #define WM8962_GPIO_FN_DRC_ACT         10
  #define WM8962_GPIO_FN_WSEQ_DONE       11
  #define WM8962_GPIO_FN_ALC_NG_ACT      12
  #define WM8962_GPIO_FN_ALC_PEAK_LIMIT  13
  #define WM8962_GPIO_FN_ALC_SATURATION  14
  #define WM8962_GPIO_FN_ALC_LEVEL_THR   15
  #define WM8962_GPIO_FN_ALC_LEVEL_LOCK  16
  #define WM8962_GPIO_FN_FIFO_ERR        17
  #define WM8962_GPIO_FN_OPCLK           18
  #define WM8962_GPIO_FN_DMICCLK         19
  #define WM8962_GPIO_FN_DMICDAT         20
  #define WM8962_GPIO_FN_MICD            21
  #define WM8962_GPIO_FN_MICSCD          22
  
  struct wm8962_pdata {
  	struct clk *mclk;
  	int gpio_base;
  	u32 gpio_init[WM8962_MAX_GPIO];
  
  	/* Setup for microphone detection, raw value to be written to
  	 * R48(0x30) - only microphone related bits will be updated.
  	 * Detection may be enabled here for use with signals brought
  	 * out on the GPIOs. */
  	u32 mic_cfg;
  
  	bool irq_active_low;
  
  	bool spk_mono;   /* Speaker outputs tied together as mono */
  
  	/**
  	 * This flag should be set if one or both IN4 inputs is wired
  	 * in a DC measurement configuration.
  	 */
  	bool in4_dc_measure;
  };
  
  #endif