6b13f685e
 김민수
BSP 최초 추가
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
|
/* 8530 Serial Communications Controller Register definitions */
#define FLAG 0x7e
/* Write Register 0 */
#define R0 0 /* Register selects */
#define R1 1
#define R2 2
#define R3 3
#define R4 4
#define R5 5
#define R6 6
#define R7 7
#define R8 8
#define R9 9
#define R10 10
#define R11 11
#define R12 12
#define R13 13
#define R14 14
#define R15 15
#define NULLCODE 0 /* Null Code */
#define POINT_HIGH 0x8 /* Select upper half of registers */
#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
#define SEND_ABORT 0x18 /* HDLC Abort */
#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
#define RES_Tx_P 0x28 /* Reset TxINT Pending */
#define ERR_RES 0x30 /* Error Reset */
#define RES_H_IUS 0x38 /* Reset highest IUS */
#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
#define RES_EOM_L 0xC0 /* Reset EOM latch */
/* Write Register 1 */
#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
#define TxINT_ENAB 0x2 /* Tx Int Enable */
#define PAR_SPEC 0x4 /* Parity is special condition */
#define RxINT_DISAB 0 /* Rx Int Disable */
#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
#define INT_ERR_Rx 0x18 /* Int on error only */
#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
/* Write Register #2 (Interrupt Vector) */
/* Write Register 3 */
#define RxENABLE 0x1 /* Rx Enable */
#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
#define ENT_HM 0x10 /* Enter Hunt Mode */
#define AUTO_ENAB 0x20 /* Auto Enables */
#define Rx5 0x0 /* Rx 5 Bits/Character */
#define Rx7 0x40 /* Rx 7 Bits/Character */
#define Rx6 0x80 /* Rx 6 Bits/Character */
#define Rx8 0xc0 /* Rx 8 Bits/Character */
/* Write Register 4 */
#define PAR_ENA 0x1 /* Parity Enable */
#define PAR_EVEN 0x2 /* Parity Even/Odd* */
#define SYNC_ENAB 0 /* Sync Modes Enable */
#define SB1 0x4 /* 1 stop bit/char */
#define SB15 0x8 /* 1.5 stop bits/char */
#define SB2 0xc /* 2 stop bits/char */
#define MONSYNC 0 /* 8 Bit Sync character */
#define BISYNC 0x10 /* 16 bit sync character */
#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
#define EXTSYNC 0x30 /* External Sync Mode */
#define X1CLK 0x0 /* x1 clock mode */
#define X16CLK 0x40 /* x16 clock mode */
#define X32CLK 0x80 /* x32 clock mode */
#define X64CLK 0xC0 /* x64 clock mode */
/* Write Register 5 */
#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
#define RTS 0x2 /* RTS */
#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
#define TxENAB 0x8 /* Tx Enable */
#define SND_BRK 0x10 /* Send Break */
#define Tx5 0x0 /* Tx 5 bits (or less)/character */
#define Tx7 0x20 /* Tx 7 bits/character */
#define Tx6 0x40 /* Tx 6 bits/character */
#define Tx8 0x60 /* Tx 8 bits/character */
#define DTR 0x80 /* DTR */
/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
/* Write Register 8 (transmit buffer) */
/* Write Register 9 (Master interrupt control) */
#define VIS 1 /* Vector Includes Status */
#define NV 2 /* No Vector */
#define DLC 4 /* Disable Lower Chain */
#define MIE 8 /* Master Interrupt Enable */
#define STATHI 0x10 /* Status high */
#define NORESET 0 /* No reset on write to R9 */
#define CHRB 0x40 /* Reset channel B */
#define CHRA 0x80 /* Reset channel A */
#define FHWRES 0xc0 /* Force hardware reset */
/* Write Register 10 (misc control bits) */
#define BIT6 1 /* 6 bit/8bit sync */
#define LOOPMODE 2 /* SDLC Loop mode */
#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
#define MARKIDLE 8 /* Mark/flag on idle */
#define GAOP 0x10 /* Go active on poll */
#define NRZ 0 /* NRZ mode */
#define NRZI 0x20 /* NRZI mode */
#define FM1 0x40 /* FM1 (transition = 1) */
#define FM0 0x60 /* FM0 (transition = 0) */
#define CRCPS 0x80 /* CRC Preset I/O */
/* Write Register 11 (Clock Mode control) */
#define TRxCXT 0 /* TRxC = Xtal output */
#define TRxCTC 1 /* TRxC = Transmit clock */
#define TRxCBR 2 /* TRxC = BR Generator Output */
#define TRxCDP 3 /* TRxC = DPLL output */
#define TRxCOI 4 /* TRxC O/I */
#define TCRTxCP 0 /* Transmit clock = RTxC pin */
#define TCTRxCP 8 /* Transmit clock = TRxC pin */
#define TCBR 0x10 /* Transmit clock = BR Generator output */
#define TCDPLL 0x18 /* Transmit clock = DPLL output */
#define RCRTxCP 0 /* Receive clock = RTxC pin */
#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
#define RCBR 0x40 /* Receive clock = BR Generator output */
#define RCDPLL 0x60 /* Receive clock = DPLL output */
#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
/* Write Register 12 (lower byte of baud rate generator time constant) */
/* Write Register 13 (upper byte of baud rate generator time constant) */
/* Write Register 14 (Misc control bits) */
#define BRENABL 1 /* Baud rate generator enable */
#define BRSRC 2 /* Baud rate generator source */
#define DTRREQ 4 /* DTR/Request function */
#define AUTOECHO 8 /* Auto Echo */
#define LOOPBAK 0x10 /* Local loopback */
#define SEARCH 0x20 /* Enter search mode */
#define RMC 0x40 /* Reset missing clock */
#define DISDPLL 0x60 /* Disable DPLL */
#define SSBR 0x80 /* Set DPLL source = BR generator */
#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
#define SFMM 0xc0 /* Set FM mode */
#define SNRZI 0xe0 /* Set NRZI mode */
/* Write Register 15 (external/status interrupt control) */
#define ZCIE 2 /* Zero count IE */
#define DCDIE 8 /* DCD IE */
#define SYNCIE 0x10 /* Sync/hunt IE */
#define CTSIE 0x20 /* CTS IE */
#define TxUIE 0x40 /* Tx Underrun/EOM IE */
#define BRKIE 0x80 /* Break/Abort IE */
/* Read Register 0 */
#define Rx_CH_AV 0x1 /* Rx Character Available */
#define ZCOUNT 0x2 /* Zero count */
#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
#define DCD 0x8 /* DCD */
#define SYNC_HUNT 0x10 /* Sync/hunt */
#define CTS 0x20 /* CTS */
#define TxEOM 0x40 /* Tx underrun */
#define BRK_ABRT 0x80 /* Break/Abort */
/* Read Register 1 */
#define ALL_SNT 0x1 /* All sent */
/* Residue Data for 8 Rx bits/char programmed */
#define RES3 0x8 /* 0/3 */
#define RES4 0x4 /* 0/4 */
#define RES5 0xc /* 0/5 */
#define RES6 0x2 /* 0/6 */
#define RES7 0xa /* 0/7 */
#define RES8 0x6 /* 0/8 */
#define RES18 0xe /* 1/8 */
#define RES28 0x0 /* 2/8 */
/* Special Rx Condition Interrupts */
#define PAR_ERR 0x10 /* Parity error */
#define Rx_OVR 0x20 /* Rx Overrun Error */
#define CRC_ERR 0x40 /* CRC/Framing Error */
#define END_FR 0x80 /* End of Frame (SDLC) */
/* Read Register 2 (channel b only) - Interrupt vector */
/* Read Register 3 (interrupt pending register) ch a only */
#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
#define CHBTxIP 0x2 /* Channel B Tx IP */
#define CHBRxIP 0x4 /* Channel B Rx IP */
#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
#define CHATxIP 0x10 /* Channel A Tx IP */
#define CHARxIP 0x20 /* Channel A Rx IP */
/* Read Register 8 (receive data register) */
/* Read Register 10 (misc status bits) */
#define ONLOOP 2 /* On loop */
#define LOOPSEND 0x10 /* Loop sending */
#define CLK2MIS 0x40 /* Two clocks missing */
#define CLK1MIS 0x80 /* One clock missing */
/* Read Register 12 (lower byte of baud rate generator constant) */
/* Read Register 13 (upper byte of baud rate generator constant) */
/* Read Register 15 (value of WR 15) */
/* Z85C30/Z85230 Enhanced SCC register definitions */
/* Write Register 7' (SDLC/HDLC Programmable Enhancements) */
#define AUTOTXF 0x01 /* Auto Tx Flag */
#define AUTOEOM 0x02 /* Auto EOM Latch Reset */
#define AUTORTS 0x04 /* Auto RTS */
#define TXDNRZI 0x08 /* TxD Pulled High in SDLC NRZI mode */
#define RXFIFOH 0x08 /* Z85230: Int on RX FIFO half full */
#define FASTDTR 0x10 /* Fast DTR/REQ Mode */
#define CRCCBCR 0x20 /* CRC Check Bytes Completely Received */
#define TXFIFOE 0x20 /* Z85230: Int on TX FIFO completely empty */
#define EXTRDEN 0x40 /* Extended Read Enabled */
/* Write Register 15 (external/status interrupt control) */
#define SHDLCE 1 /* SDLC/HDLC Enhancements Enable */
#define FIFOE 4 /* FIFO Enable */
/* Read Register 6 (frame status FIFO) */
#define BCLSB 0xff /* LSB of 14 bits count */
/* Read Register 7 (frame status FIFO) */
#define BCMSB 0x3f /* MSB of 14 bits count */
#define FDA 0x40 /* FIFO Data Available Status */
#define FOS 0x80 /* FIFO Overflow Status */
|