6b13f685e
김민수
BSP 최초 추가
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
|
/* drivers/atm/uPD98401.h - NEC uPD98401 (SAR) declarations */
/* Written 1995 by Werner Almesberger, EPFL LRC */
#ifndef DRIVERS_ATM_uPD98401_H
#define DRIVERS_ATM_uPD98401_H
#define MAX_CRAM_SIZE (1 << 18) /* 2^18 words */
#define RAM_INCREMENT 1024 /* check in 4 kB increments */
#define uPD98401_PORTS 0x24 /* probably more ? */
/*
* Commands
*/
#define uPD98401_OPEN_CHAN 0x20000000 /* open channel */
#define uPD98401_CHAN_ADDR 0x0003fff8 /* channel address */
#define uPD98401_CHAN_ADDR_SHIFT 3
#define uPD98401_CLOSE_CHAN 0x24000000 /* close channel */
#define uPD98401_CHAN_RT 0x02000000 /* RX/TX (0 TX, 1 RX) */
#define uPD98401_DEACT_CHAN 0x28000000 /* deactivate channel */
#define uPD98401_TX_READY 0x30000000 /* TX ready */
#define uPD98401_ADD_BAT 0x34000000 /* add batches */
#define uPD98401_POOL 0x000f0000 /* pool number */
#define uPD98401_POOL_SHIFT 16
#define uPD98401_POOL_NUMBAT 0x0000ffff /* number of batches */
#define uPD98401_NOP 0x3f000000 /* NOP */
#define uPD98401_IND_ACC 0x00000000 /* Indirect Access */
#define uPD98401_IA_RW 0x10000000 /* Read/Write (0 W, 1 R) */
#define uPD98401_IA_B3 0x08000000 /* Byte select, 1 enable */
#define uPD98401_IA_B2 0x04000000
#define uPD98401_IA_B1 0x02000000
#define uPD98401_IA_B0 0x01000000
#define uPD98401_IA_BALL 0x0f000000 /* whole longword */
#define uPD98401_IA_TGT 0x000c0000 /* Target */
#define uPD98401_IA_TGT_SHIFT 18
#define uPD98401_IA_TGT_CM 0 /* - Control Memory */
#define uPD98401_IA_TGT_SAR 1 /* - uPD98401 registers */
#define uPD98401_IA_TGT_PHY 3 /* - PHY device */
#define uPD98401_IA_ADDR 0x0003ffff
/*
* Command Register Status
*/
#define uPD98401_BUSY 0x80000000 /* SAR is busy */
#define uPD98401_LOCKED 0x40000000 /* SAR is locked by other CPU */
/*
* Indications
*/
/* Normal (AAL5) Receive Indication */
#define uPD98401_AAL5_UINFO 0xffff0000 /* user-supplied information */
#define uPD98401_AAL5_UINFO_SHIFT 16
#define uPD98401_AAL5_SIZE 0x0000ffff /* PDU size (in _CELLS_ !!) */
#define uPD98401_AAL5_CHAN 0x7fff0000 /* Channel number */
#define uPD98401_AAL5_CHAN_SHIFT 16
#define uPD98401_AAL5_ERR 0x00008000 /* Error indication */
#define uPD98401_AAL5_CI 0x00004000 /* Congestion Indication */
#define uPD98401_AAL5_CLP 0x00002000 /* CLP (>= 1 cell had CLP=1) */
#define uPD98401_AAL5_ES 0x00000f00 /* Error Status */
#define uPD98401_AAL5_ES_SHIFT 8
#define uPD98401_AAL5_ES_NONE 0 /* No error */
#define uPD98401_AAL5_ES_FREE 1 /* Receiver free buf underflow */
#define uPD98401_AAL5_ES_FIFO 2 /* Receiver FIFO overrun */
#define uPD98401_AAL5_ES_TOOBIG 3 /* Maximum length violation */
#define uPD98401_AAL5_ES_CRC 4 /* CRC error */
#define uPD98401_AAL5_ES_ABORT 5 /* User abort */
#define uPD98401_AAL5_ES_LENGTH 6 /* Length violation */
#define uPD98401_AAL5_ES_T1 7 /* T1 error (timeout) */
#define uPD98401_AAL5_ES_DEACT 8 /* Deactivated with DEACT_CHAN */
#define uPD98401_AAL5_POOL 0x0000001f /* Free buffer pool number */
/* Raw Cell Indication */
#define uPD98401_RAW_UINFO uPD98401_AAL5_UINFO
#define uPD98401_RAW_UINFO_SHIFT uPD98401_AAL5_UINFO_SHIFT
#define uPD98401_RAW_HEC 0x000000ff /* HEC */
#define uPD98401_RAW_CHAN uPD98401_AAL5_CHAN
#define uPD98401_RAW_CHAN_SHIFT uPD98401_AAL5_CHAN_SHIFT
/* Transmit Indication */
#define uPD98401_TXI_CONN 0x7fff0000 /* Connection Number */
#define uPD98401_TXI_CONN_SHIFT 16
#define uPD98401_TXI_ACTIVE 0x00008000 /* Channel remains active */
#define uPD98401_TXI_PQP 0x00007fff /* Packet Queue Pointer */
/*
* Directly Addressable Registers
*/
#define uPD98401_GMR 0x00 /* General Mode Register */
#define uPD98401_GSR 0x01 /* General Status Register */
#define uPD98401_IMR 0x02 /* Interrupt Mask Register */
#define uPD98401_RQU 0x03 /* Receive Queue Underrun */
#define uPD98401_RQA 0x04 /* Receive Queue Alert */
#define uPD98401_ADDR 0x05 /* Last Burst Address */
#define uPD98401_VER 0x06 /* Version Number */
#define uPD98401_SWR 0x07 /* Software Reset */
#define uPD98401_CMR 0x08 /* Command Register */
#define uPD98401_CMR_L 0x09 /* Command Register and Lock/Unlock */
#define uPD98401_CER 0x0a /* Command Extension Register */
#define uPD98401_CER_L 0x0b /* Command Ext Reg and Lock/Unlock */
#define uPD98401_MSH(n) (0x10+(n)) /* Mailbox n Start Address High */
#define uPD98401_MSL(n) (0x14+(n)) /* Mailbox n Start Address High */
#define uPD98401_MBA(n) (0x18+(n)) /* Mailbox n Bottom Address */
#define uPD98401_MTA(n) (0x1c+(n)) /* Mailbox n Tail Address */
#define uPD98401_MWA(n) (0x20+(n)) /* Mailbox n Write Address */
/* GMR is at 0x00 */
#define uPD98401_GMR_ONE 0x80000000 /* Must be set to one */
#define uPD98401_GMR_SLM 0x40000000 /* Address mode (0 word, 1 byte) */
#define uPD98401_GMR_CPE 0x00008000 /* Control Memory Parity Enable */
#define uPD98401_GMR_LP 0x00004000 /* Loopback */
#define uPD98401_GMR_WA 0x00002000 /* Early Bus Write Abort/RDY */
#define uPD98401_GMR_RA 0x00001000 /* Early Read Abort/RDY */
#define uPD98401_GMR_SZ 0x00000f00 /* Burst Size Enable */
#define uPD98401_BURST16 0x00000800 /* 16-word burst */
#define uPD98401_BURST8 0x00000400 /* 8-word burst */
#define uPD98401_BURST4 0x00000200 /* 4-word burst */
#define uPD98401_BURST2 0x00000100 /* 2-word burst */
#define uPD98401_GMR_AD 0x00000080 /* Address (burst resolution) Disable */
#define uPD98401_GMR_BO 0x00000040 /* Byte Order (0 little, 1 big) */
#define uPD98401_GMR_PM 0x00000020 /* Bus Parity Mode (0 byte, 1 word)*/
#define uPD98401_GMR_PC 0x00000010 /* Bus Parity Control (0even,1odd) */
#define uPD98401_GMR_BPE 0x00000008 /* Bus Parity Enable */
#define uPD98401_GMR_DR 0x00000004 /* Receive Drop Mode (0drop,1don't)*/
#define uPD98401_GMR_SE 0x00000002 /* Shapers Enable */
#define uPD98401_GMR_RE 0x00000001 /* Receiver Enable */
/* GSR is at 0x01, IMR is at 0x02 */
#define uPD98401_INT_PI 0x80000000 /* PHY interrupt */
#define uPD98401_INT_RQA 0x40000000 /* Receive Queue Alert */
#define uPD98401_INT_RQU 0x20000000 /* Receive Queue Underrun */
#define uPD98401_INT_RD 0x10000000 /* Receiver Deactivated */
#define uPD98401_INT_SPE 0x08000000 /* System Parity Error */
#define uPD98401_INT_CPE 0x04000000 /* Control Memory Parity Error */
#define uPD98401_INT_SBE 0x02000000 /* System Bus Error */
#define uPD98401_INT_IND 0x01000000 /* Initialization Done */
#define uPD98401_INT_RCR 0x0000ff00 /* Raw Cell Received */
#define uPD98401_INT_RCR_SHIFT 8
#define uPD98401_INT_MF 0x000000f0 /* Mailbox Full */
#define uPD98401_INT_MF_SHIFT 4
#define uPD98401_INT_MM 0x0000000f /* Mailbox Modified */
/* VER is at 0x06 */
#define uPD98401_MAJOR 0x0000ff00 /* Major revision */
#define uPD98401_MAJOR_SHIFT 8
#define uPD98401_MINOR 0x000000ff /* Minor revision */
/*
* Indirectly Addressable Registers
*/
#define uPD98401_IM(n) (0x40000+(n)) /* Scheduler n I and M */
#define uPD98401_X(n) (0x40010+(n)) /* Scheduler n X */
#define uPD98401_Y(n) (0x40020+(n)) /* Scheduler n Y */
#define uPD98401_PC(n) (0x40030+(n)) /* Scheduler n P, C, p and c */
#define uPD98401_PS(n) (0x40040+(n)) /* Scheduler n priority and status */
/* IM contents */
#define uPD98401_IM_I 0xff000000 /* I */
#define uPD98401_IM_I_SHIFT 24
#define uPD98401_IM_M 0x00ffffff /* M */
/* PC contents */
#define uPD98401_PC_P 0xff000000 /* P */
#define uPD98401_PC_P_SHIFT 24
#define uPD98401_PC_C 0x00ff0000 /* C */
#define uPD98401_PC_C_SHIFT 16
#define uPD98401_PC_p 0x0000ff00 /* p */
#define uPD98401_PC_p_SHIFT 8
#define uPD98401_PC_c 0x000000ff /* c */
/* PS contents */
#define uPD98401_PS_PRIO 0xf0 /* Priority level (0 high, 15 low) */
#define uPD98401_PS_PRIO_SHIFT 4
#define uPD98401_PS_S 0x08 /* Scan - must be 0 (internal) */
#define uPD98401_PS_R 0x04 /* Round Robin (internal) */
#define uPD98401_PS_A 0x02 /* Active (internal) */
#define uPD98401_PS_E 0x01 /* Enabled */
#define uPD98401_TOS 0x40100 /* Top of Stack Control Memory Address */
#define uPD98401_SMA 0x40200 /* Shapers Control Memory Start Address */
#define uPD98401_PMA 0x40201 /* Receive Pool Control Memory Start Address */
#define uPD98401_T1R 0x40300 /* T1 Register */
#define uPD98401_VRR 0x40301 /* VPI/VCI Reduction Register/Recv. Shutdown */
#define uPD98401_TSR 0x40302 /* Time-Stamp Register */
/* VRR is at 0x40301 */
#define uPD98401_VRR_SDM 0x80000000 /* Shutdown Mode */
#define uPD98401_VRR_SHIFT 0x000f0000 /* VPI/VCI Shift */
#define uPD98401_VRR_SHIFT_SHIFT 16
#define uPD98401_VRR_MASK 0x0000ffff /* VPI/VCI mask */
/*
* TX packet descriptor
*/
#define uPD98401_TXPD_SIZE 16 /* descriptor size (in bytes) */
#define uPD98401_TXPD_V 0x80000000 /* Valid bit */
#define uPD98401_TXPD_DP 0x40000000 /* Descriptor (1) or Pointer (0) */
#define uPD98401_TXPD_SM 0x20000000 /* Single (1) or Multiple (0) */
#define uPD98401_TXPD_CLPM 0x18000000 /* CLP mode */
#define uPD98401_CLPM_0 0 /* 00 CLP = 0 */
#define uPD98401_CLPM_1 3 /* 11 CLP = 1 */
#define uPD98401_CLPM_LAST 1 /* 01 CLP unless last cell */
#define uPD98401_TXPD_CLPM_SHIFT 27
#define uPD98401_TXPD_PTI 0x07000000 /* PTI pattern */
#define uPD98401_TXPD_PTI_SHIFT 24
#define uPD98401_TXPD_GFC 0x00f00000 /* GFC pattern */
#define uPD98401_TXPD_GFC_SHIFT 20
#define uPD98401_TXPD_C10 0x00040000 /* insert CRC-10 */
#define uPD98401_TXPD_AAL5 0x00020000 /* AAL5 processing */
#define uPD98401_TXPD_MB 0x00010000 /* TX mailbox number */
#define uPD98401_TXPD_UU 0x0000ff00 /* CPCS-UU */
#define uPD98401_TXPD_UU_SHIFT 8
#define uPD98401_TXPD_CPI 0x000000ff /* CPI */
/*
* TX buffer descriptor
*/
#define uPD98401_TXBD_SIZE 8 /* descriptor size (in bytes) */
#define uPD98401_TXBD_LAST 0x80000000 /* last buffer in packet */
/*
* TX VC table
*/
/* 1st word has the same structure as in a TX packet descriptor */
#define uPD98401_TXVC_L 0x80000000 /* last buffer */
#define uPD98401_TXVC_SHP 0x0f000000 /* shaper number */
#define uPD98401_TXVC_SHP_SHIFT 24
#define uPD98401_TXVC_VPI 0x00ff0000 /* VPI */
#define uPD98401_TXVC_VPI_SHIFT 16
#define uPD98401_TXVC_VCI 0x0000ffff /* VCI */
#define uPD98401_TXVC_QRP 6 /* Queue Read Pointer is in word 6 */
/*
* RX free buffer pools descriptor
*/
#define uPD98401_RXFP_ALERT 0x70000000 /* low water mark */
#define uPD98401_RXFP_ALERT_SHIFT 28
#define uPD98401_RXFP_BFSZ 0x0f000000 /* buffer size, 64*2^n */
#define uPD98401_RXFP_BFSZ_SHIFT 24
#define uPD98401_RXFP_BTSZ 0x00ff0000 /* batch size, n+1 */
#define uPD98401_RXFP_BTSZ_SHIFT 16
#define uPD98401_RXFP_REMAIN 0x0000ffff /* remaining batches in pool */
/*
* RX VC table
*/
#define uPD98401_RXVC_BTSZ 0xff000000 /* remaining free buffers in batch */
#define uPD98401_RXVC_BTSZ_SHIFT 24
#define uPD98401_RXVC_MB 0x00200000 /* RX mailbox number */
#define uPD98401_RXVC_POOL 0x001f0000 /* free buffer pool number */
#define uPD98401_RXVC_POOL_SHIFT 16
#define uPD98401_RXVC_UINFO 0x0000ffff /* user-supplied information */
#define uPD98401_RXVC_T1 0xffff0000 /* T1 timestamp */
#define uPD98401_RXVC_T1_SHIFT 16
#define uPD98401_RXVC_PR 0x00008000 /* Packet Reception, 1 if busy */
#define uPD98401_RXVC_DR 0x00004000 /* FIFO Drop */
#define uPD98401_RXVC_OD 0x00001000 /* Drop OAM cells */
#define uPD98401_RXVC_AR 0x00000800 /* AAL5 or raw cell; 1 if AAL5 */
#define uPD98401_RXVC_MAXSEG 0x000007ff /* max number of segments per PDU */
#define uPD98401_RXVC_REM 0xfffe0000 /* remaining words in curr buffer */
#define uPD98401_RXVC_REM_SHIFT 17
#define uPD98401_RXVC_CLP 0x00010000 /* CLP received */
#define uPD98401_RXVC_BFA 0x00008000 /* Buffer Assigned */
#define uPD98401_RXVC_BTA 0x00004000 /* Batch Assigned */
#define uPD98401_RXVC_CI 0x00002000 /* Congestion Indication */
#define uPD98401_RXVC_DD 0x00001000 /* Dropping incoming cells */
#define uPD98401_RXVC_DP 0x00000800 /* like PR ? */
#define uPD98401_RXVC_CURSEG 0x000007ff /* Current Segment count */
/*
* RX lookup table
*/
#define uPD98401_RXLT_ENBL 0x8000 /* Enable */
#endif
|