/*
   * linux/arch/arm/mach-omap2/board-omap3evm.c
   *
   * Copyright (C) 2008 Guangzhou EMA-Tech
   *
   * Modified from mach-omap2/board-omap3evm.c
   *
   * Initial code: Syed Mohammed Khasim
   *
   * This program is free software; you can redistribute it and/or modify
   * it under the terms of the GNU General Public License version 2 as
   * published by the Free Software Foundation.
   */
  
  #include <linux/kernel.h>
  #include <linux/init.h>
  #include <linux/platform_device.h>
  #include <linux/delay.h>
  #include <linux/err.h>
  #include <linux/clk.h>
  #include <linux/io.h>
  #include <linux/leds.h>
  #include <linux/gpio.h>
  #include <linux/input.h>
  #include <linux/gpio_keys.h>
  
  #include <linux/regulator/fixed.h>
  #include <linux/regulator/machine.h>
  #include <linux/i2c/twl.h>
  #include <linux/mmc/host.h>
  #include <linux/input/matrix_keypad.h>
  #include <linux/spi/spi.h>
  #include <linux/interrupt.h>
  #include <linux/smsc911x.h>
  #include <linux/platform_data/at24.h>
  #include <linux/usb/phy.h>
  
  #include <asm/mach-types.h>
  #include <asm/mach/arch.h>
  #include <asm/mach/map.h>
  #include <asm/mach/flash.h>
  
  #include "common.h"
  #include "gpmc.h"
  #include <linux/platform_data/mtd-nand-omap2.h>
  #include <video/omapdss.h>
  #include <video/omap-panel-data.h>
  
  #include <linux/platform_data/spi-omap2-mcspi.h>
  
  #include "sdram-micron-mt46h32m32lf-6.h"
  #include "mux.h"
  #include "hsmmc.h"
  #include "common-board-devices.h"
  
  #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
  #include "gpmc-smsc911x.h"
  
  #define OMAP3STALKER_ETHR_START	0x2c000000
  #define OMAP3STALKER_ETHR_SIZE	1024
  #define OMAP3STALKER_ETHR_GPIO_IRQ	19
  #define OMAP3STALKER_SMC911X_CS	5
  
  static struct omap_smsc911x_platform_data smsc911x_cfg = {
  	.cs             = OMAP3STALKER_SMC911X_CS,
  	.gpio_irq       = OMAP3STALKER_ETHR_GPIO_IRQ,
  	.gpio_reset     = -EINVAL,
  	.flags		= (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
  };
  
  static inline void __init omap3stalker_init_eth(void)
  {
  	omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
  	gpmc_smsc911x_init(&smsc911x_cfg);
  }
  
  #else
  static inline void __init omap3stalker_init_eth(void)
  {
  	return;
  }
  #endif
  
  /*
   * OMAP3 DSS control signals
   */
  
  #define DSS_ENABLE_GPIO	199
  #define LCD_PANEL_BKLIGHT_GPIO	210
  #define ENABLE_VPLL2_DEV_GRP	0xE0
  
  static void __init omap3_stalker_display_init(void)
  {
  	return;
  }
  static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
  	.name                   = "dvi",
  	.source                 = "tfp410.0",
  	.i2c_bus_num            = -1,
  };
  
  static struct platform_device omap3stalker_dvi_connector_device = {
  	.name                   = "connector-dvi",
  	.id                     = 0,
  	.dev.platform_data      = &omap3stalker_dvi_connector_pdata,
  };
  
  static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
  	.name                   = "tfp410.0",
  	.source                 = "dpi.0",
  	.data_lines             = 24,
  	.power_down_gpio        = DSS_ENABLE_GPIO,
  };
  
  static struct platform_device omap3stalker_tfp410_device = {
  	.name                   = "tfp410",
  	.id                     = 0,
  	.dev.platform_data      = &omap3stalker_tfp410_pdata,
  };
  
  static struct connector_atv_platform_data omap3stalker_tv_pdata = {
  	.name = "tv",
  	.source = "venc.0",
  #if defined(CONFIG_OMAP2_VENC_OUT_TYPE_SVIDEO)
  	.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
  #elif defined(CONFIG_OMAP2_VENC_OUT_TYPE_COMPOSITE)
  	.connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
  #endif
  	.invert_polarity = false,
  };
  
  static struct platform_device omap3stalker_tv_connector_device = {
  	.name                   = "connector-analog-tv",
  	.id                     = 0,
  	.dev.platform_data      = &omap3stalker_tv_pdata,
  };
  
  static struct omap_dss_board_info omap3_stalker_dss_data = {
  	.default_display_name = "dvi",
  };
  
  static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
  	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
  };
  
  static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
  	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
  };
  
  /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
  static struct regulator_init_data omap3stalker_vmmc1 = {
  	.constraints		= {
  		.min_uV			= 1850000,
  		.max_uV			= 3150000,
  		.valid_modes_mask	= REGULATOR_MODE_NORMAL
  		| REGULATOR_MODE_STANDBY,
  		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
  		| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
  	},
  	.num_consumer_supplies	= ARRAY_SIZE(omap3stalker_vmmc1_supply),
  	.consumer_supplies	= omap3stalker_vmmc1_supply,
  };
  
  /* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
  static struct regulator_init_data omap3stalker_vsim = {
  	.constraints		= {
  		.min_uV			= 1800000,
  		.max_uV			= 3000000,
  		.valid_modes_mask	= REGULATOR_MODE_NORMAL
  		| REGULATOR_MODE_STANDBY,
  		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
  		| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
  	},
  	.num_consumer_supplies	= ARRAY_SIZE(omap3stalker_vsim_supply),
  	.consumer_supplies	= omap3stalker_vsim_supply,
  };
  
  static struct omap2_hsmmc_info mmc[] = {
  	{
  		.mmc		= 1,
  		.caps		= MMC_CAP_4_BIT_DATA,
  		.gpio_cd	= -EINVAL,
  		.gpio_wp	= 23,
  		.deferred	= true,
  	 },
  	{}			/* Terminator */
  };
  
  static struct gpio_keys_button gpio_buttons[] = {
  	{
  	 .code		= BTN_EXTRA,
  	 .gpio		= 18,
  	 .desc		= "user",
  	 .wakeup	= 1,
  	 },
  };
  
  static struct gpio_keys_platform_data gpio_key_info = {
  	.buttons	= gpio_buttons,
  	.nbuttons	= ARRAY_SIZE(gpio_buttons),
  };
  
  static struct platform_device keys_gpio = {
  	.name		= "gpio-keys",
  	.id		= -1,
  	.dev		= {
  		.platform_data	= &gpio_key_info,
  	},
  };
  
  static struct gpio_led gpio_leds[] = {
  	{
  	 .name			= "stalker:D8:usr0",
  	 .default_trigger	= "default-on",
  	 .gpio			= 126,
  	 },
  	{
  	 .name			= "stalker:D9:usr1",
  	 .default_trigger	= "default-on",
  	 .gpio			= 127,
  	 },
  	{
  	 .name			= "stalker:D3:mmc0",
  	 .gpio			= -EINVAL,	/* gets replaced */
  	 .active_low		= true,
  	 .default_trigger	= "mmc0",
  	 },
  	{
  	 .name			= "stalker:D4:heartbeat",
  	 .gpio			= -EINVAL,	/* gets replaced */
  	 .active_low		= true,
  	 .default_trigger	= "heartbeat",
  	 },
  };
  
  static struct gpio_led_platform_data gpio_led_info = {
  	.leds		= gpio_leds,
  	.num_leds	= ARRAY_SIZE(gpio_leds),
  };
  
  static struct platform_device leds_gpio = {
  	.name	= "leds-gpio",
  	.id	= -1,
  	.dev	= {
  		.platform_data	= &gpio_led_info,
  	},
  };
  
  static int
  omap3stalker_twl_gpio_setup(struct device *dev,
  			    unsigned gpio, unsigned ngpio)
  {
  	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
  	mmc[0].gpio_cd = gpio + 0;
  	omap_hsmmc_late_init(mmc);
  
  	/*
  	 * Most GPIOs are for USB OTG.  Some are mostly sent to
  	 * the P2 connector; notably LEDA for the LCD backlight.
  	 */
  
  	/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
  	gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
  			 "EN_LCD_BKL");
  
  	/* gpio + 7 == DVI Enable */
  	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
  
  	/* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
  	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
  	/* GPIO + 13 == ledsync (out, heartbeat) */
  	gpio_leds[3].gpio = gpio + 13;
  
  	platform_device_register(&leds_gpio);
  	return 0;
  }
  
  static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
  	.use_leds	= true,
  	.setup		= omap3stalker_twl_gpio_setup,
  };
  
  static uint32_t board_keymap[] = {
  	KEY(0, 0, KEY_LEFT),
  	KEY(0, 1, KEY_DOWN),
  	KEY(0, 2, KEY_ENTER),
  	KEY(0, 3, KEY_M),
  
  	KEY(1, 0, KEY_RIGHT),
  	KEY(1, 1, KEY_UP),
  	KEY(1, 2, KEY_I),
  	KEY(1, 3, KEY_N),
  
  	KEY(2, 0, KEY_A),
  	KEY(2, 1, KEY_E),
  	KEY(2, 2, KEY_J),
  	KEY(2, 3, KEY_O),
  
  	KEY(3, 0, KEY_B),
  	KEY(3, 1, KEY_F),
  	KEY(3, 2, KEY_K),
  	KEY(3, 3, KEY_P)
  };
  
  static struct matrix_keymap_data board_map_data = {
  	.keymap		= board_keymap,
  	.keymap_size	= ARRAY_SIZE(board_keymap),
  };
  
  static struct twl4030_keypad_data omap3stalker_kp_data = {
  	.keymap_data	= &board_map_data,
  	.rows		= 4,
  	.cols		= 4,
  	.rep		= 1,
  };
  
  static struct twl4030_platform_data omap3stalker_twldata = {
  	/* platform_data for children goes here */
  	.keypad		= &omap3stalker_kp_data,
  	.gpio		= &omap3stalker_gpio_data,
  	.vmmc1		= &omap3stalker_vmmc1,
  	.vsim		= &omap3stalker_vsim,
  };
  
  static struct at24_platform_data fram_info = {
  	.byte_len	= (64 * 1024) / 8,
  	.page_size	= 8192,
  	.flags		= AT24_FLAG_ADDR16 | AT24_FLAG_IRUGO,
  };
  
  static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
  	{
  	 I2C_BOARD_INFO("24c64", 0x50),
  	 .flags		= I2C_CLIENT_WAKE,
  	 .platform_data	= &fram_info,
  	 },
  };
  
  static int __init omap3_stalker_i2c_init(void)
  {
  	omap3_pmic_get_config(&omap3stalker_twldata,
  			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
  			TWL_COMMON_PDATA_AUDIO,
  			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
  
  	omap3stalker_twldata.vdac->constraints.apply_uV = true;
  	omap3stalker_twldata.vpll2->constraints.apply_uV = true;
  	omap3stalker_twldata.vpll2->constraints.name = "VDVI";
  
  	omap3_pmic_init("twl4030", &omap3stalker_twldata);
  	omap_register_i2c_bus(2, 400, NULL, 0);
  	omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
  			      ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
  	return 0;
  }
  
  #define OMAP3_STALKER_TS_GPIO	175
  
  static struct usbhs_phy_data phy_data[] __initdata = {
  	{
  		.port = 2,
  		.reset_gpio = 21,
  		.vcc_gpio = -EINVAL,
  	},
  };
  
  static struct platform_device *omap3_stalker_devices[] __initdata = {
  	&keys_gpio,
  	&omap3stalker_tfp410_device,
  	&omap3stalker_dvi_connector_device,
  	&omap3stalker_tv_connector_device,
  };
  
  static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
  	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
  };
  
  #ifdef CONFIG_OMAP_MUX
  static struct omap_board_mux board_mux[] __initdata = {
  	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
  		  OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
  	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
  		  OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
  	{.reg_offset = OMAP_MUX_TERMINATOR},
  };
  #endif
  
  static struct regulator_consumer_supply dummy_supplies[] = {
  	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
  	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
  };
  
  static void __init omap3_stalker_init(void)
  {
  	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
  	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
  
  	omap_mux_init_gpio(23, OMAP_PIN_INPUT);
  	omap_hsmmc_init(mmc);
  
  	omap3_stalker_i2c_init();
  
  	platform_add_devices(omap3_stalker_devices,
  			     ARRAY_SIZE(omap3_stalker_devices));
  
  	omap_display_init(&omap3_stalker_dss_data);
  
  	omap_serial_init();
  	omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
  	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
  	usb_musb_init(NULL);
  
  	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
  	usbhs_init(&usbhs_bdata);
  	omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
  
  	omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
  	omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
  
  	omap3stalker_init_eth();
  	omap3_stalker_display_init();
  /* Ensure SDRC pins are mux'd for self-refresh */
  	omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
  	omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
  }
  
  MACHINE_START(SBC3530, "OMAP3 STALKER")
  	/* Maintainer: Jason Lam -lzg@ema-tech.com */
  	.atag_offset		= 0x100,
  	.map_io			= omap3_map_io,
  	.init_early		= omap35xx_init_early,
  	.init_irq		= omap3_init_irq,
  	.handle_irq		= omap3_intc_handle_irq,
  	.init_machine		= omap3_stalker_init,
  	.init_late		= omap35xx_init_late,
  	.init_time		= omap3_secure_sync32k_timer_init,
  	.restart		= omap3xxx_restart,
  MACHINE_END