6b13f685e
 김민수
BSP 최초 추가
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
|
c-qcam - Connectix Color QuickCam video4linux kernel driver
Copyright (C) 1999 Dave Forrest <drf5n@virginia.edu>
released under GNU GPL.
1999-12-08 Dave Forrest, written with kernel version 2.2.12 in mind
Table of Contents
1.0 Introduction
2.0 Compilation, Installation, and Configuration
3.0 Troubleshooting
4.0 Future Work / current work arounds
9.0 Sample Program, v4lgrab
10.0 Other Information
1.0 Introduction
The file ../../drivers/media/parport/c-qcam.c is a device driver for
the Logitech (nee Connectix) parallel port interface color CCD camera.
This is a fairly inexpensive device for capturing images. Logitech
does not currently provide information for developers, but many people
have engineered several solutions for non-Microsoft use of the Color
Quickcam.
1.1 Motivation
I spent a number of hours trying to get my camera to work, and I
hope this document saves you some time. My camera will not work with
the 2.2.13 kernel as distributed, but with a few patches to the
module, I was able to grab some frames. See 4.0, Future Work.
2.0 Compilation, Installation, and Configuration
The c-qcam depends on parallel port support, video4linux, and the
Color Quickcam. It is also nice to have the parallel port readback
support enabled. I enabled these as modules during the kernel
configuration. The appropriate flags are:
CONFIG_PRINTER M for lp.o, parport.o parport_pc.o modules
CONFIG_PNP_PARPORT M for autoprobe.o IEEE1284 readback module
CONFIG_PRINTER_READBACK M for parport_probe.o IEEE1284 readback module
CONFIG_VIDEO_DEV M for videodev.o video4linux module
CONFIG_VIDEO_CQCAM M for c-qcam.o Color Quickcam module
With these flags, the kernel should compile and install the modules.
To record and monitor the compilation, I use:
(make zlilo ; \
make modules; \
make modules_install ;
depmod -a ) &>log &
less log # then a capital 'F' to watch the progress
But that is my personal preference.
2.2 Configuration
The configuration requires module configuration and device
configuration. The following sections detail these procedures.
2.1 Module Configuration
Using modules requires a bit of work to install and pass the
parameters. Understand that entries in /etc/modprobe.d/*.conf of:
alias parport_lowlevel parport_pc
options parport_pc io=0x378 irq=none
alias char-major-81 videodev
alias char-major-81-0 c-qcam
2.2 Device Configuration
At this point, we need to ensure that the device files exist.
Video4linux used the /dev/video* files, and we want to attach the
Quickcam to one of these.
ls -lad /dev/video* # should produce a list of the video devices
If the video devices do not exist, you can create them with:
su
cd /dev
for ii in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ; do
mknod video$ii c 81 $ii # char-major-81-[0-16]
chown root.root video$ii # owned by root
chmod 600 video$ii # read/writable by root only
done
Lots of people connect video0 to video and bttv, but you might want
your c-qcam to mean something more:
ln -s video0 c-qcam # make /dev/c-qcam a working file
ln -s c-qcam video # make /dev/c-qcam your default video source
But these are conveniences. The important part is to make the proper
special character files with the right major and minor numbers. All
of the special device files are listed in ../devices.txt. If you
would like the c-qcam readable by non-root users, you will need to
change the permissions.
3.0 Troubleshooting
If the sample program below, v4lgrab, gives you output then
everything is working.
v4lgrab | wc # should give you a count of characters
Otherwise, you have some problem.
The c-qcam is IEEE1284 compatible, so if you are using the proc file
system (CONFIG_PROC_FS), the parallel printer support
(CONFIG_PRINTER), the IEEE 1284 system,(CONFIG_PRINTER_READBACK), you
should be able to read some identification from your quickcam with
modprobe -v parport
modprobe -v parport_probe
cat /proc/parport/PORTNUMBER/autoprobe
Returns:
CLASS:MEDIA;
MODEL:Color QuickCam 2.0;
MANUFACTURER:Connectix;
A good response to this indicates that your color quickcam is alive
and well. A common problem is that the current driver does not
reliably detect a c-qcam, even though one is attached. In this case,
modprobe -v c-qcam
or
insmod -v c-qcam
Returns a message saying "Device or resource busy" Development is
currently underway, but a workaround is to patch the module to skip
the detection code and attach to a defined port. Check the
video4linux mailing list and archive for more current information.
3.1 Checklist:
Can you get an image?
v4lgrab >qcam.ppm ; wc qcam.ppm ; xv qcam.ppm
Is a working c-qcam connected to the port?
grep ^ /proc/parport/?/autoprobe
Do the /dev/video* files exist?
ls -lad /dev/video
Is the c-qcam module loaded?
modprobe -v c-qcam ; lsmod
Does the camera work with alternate programs? cqcam, etc?
4.0 Future Work / current workarounds
It is hoped that this section will soon become obsolete, but if it
isn't, you might try patching the c-qcam module to add a parport=xxx
option as in the bw-qcam module so you can specify the parallel port:
insmod -v c-qcam parport=0
And bypass the detection code, see ../../drivers/char/c-qcam.c and
look for the 'qc_detect' code and call.
Note that there is work in progress to change the video4linux API,
this work is documented at the video4linux2 site listed below.
9.0 --- A sample program using v4lgrabber,
v4lgrab is a simple image grabber that will copy a frame from the
first video device, /dev/video0 to standard output in portable pixmap
format (.ppm) To produce .jpg output, you can use it like this:
'v4lgrab | convert - c-qcam.jpg'
10.0 --- Other Information
Use the ../../Maintainers file, particularly the VIDEO FOR LINUX and PARALLEL
PORT SUPPORT sections
The video4linux page:
http://linuxtv.org
The V4L2 API spec:
http://v4l2spec.bytesex.org/
Some web pages about the quickcams:
http://www.pingouin-land.com/howto/QuickCam-HOWTO.html
http://www.crynwr.com/qcpc/ QuickCam Third-Party Drivers
http://www.crynwr.com/qcpc/re.html Some Reverse Engineering
http://www.wirelesscouch.net/software/gqcam/ v4l client
http://phobos.illtel.denver.co.us/pub/qcread/ doesn't use v4l
ftp://ftp.cs.unm.edu/pub/chris/quickcam/ Has lots of drivers
http://www.cs.duke.edu/~reynolds/quickcam/ Has lots of information
|