6b13f685e
 김민수
BSP 최초 추가
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
Kernel driver amc6821
=====================
Supported chips:
Texas Instruments AMC6821
Prefix: 'amc6821'
Addresses scanned: 0x18, 0x19, 0x1a, 0x2c, 0x2d, 0x2e, 0x4c, 0x4d, 0x4e
Datasheet: http://focus.ti.com/docs/prod/folders/print/amc6821.html
Authors:
Tomaz Mertelj <tomaz.mertelj@guest.arnes.si>
Description
-----------
This driver implements support for the Texas Instruments amc6821 chip.
The chip has one on-chip and one remote temperature sensor and one pwm fan
regulator.
The pwm can be controlled either from software or automatically.
The driver provides the following sensor accesses in sysfs:
temp1_input ro on-chip temperature
temp1_min rw "
temp1_max rw "
temp1_crit rw "
temp1_min_alarm ro "
temp1_max_alarm ro "
temp1_crit_alarm ro "
temp2_input ro remote temperature
temp2_min rw "
temp2_max rw "
temp2_crit rw "
temp2_min_alarm ro "
temp2_max_alarm ro "
temp2_crit_alarm ro "
temp2_fault ro "
fan1_input ro tachometer speed
fan1_min rw "
fan1_max rw "
fan1_fault ro "
fan1_div rw Fan divisor can be either 2 or 4.
pwm1 rw pwm1
pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled
by remote temperature, 3=fan controlled by
combination of the on-chip temperature and
remote-sensor temperature,
pwm1_auto_channels_temp ro 1 if pwm_enable==2, 3 if pwm_enable==3
pwm1_auto_point1_pwm ro Hardwired to 0, shared for both
temperature channels.
pwm1_auto_point2_pwm rw This value is shared for both temperature
channels.
pwm1_auto_point3_pwm rw Hardwired to 255, shared for both
temperature channels.
temp1_auto_point1_temp ro Hardwired to temp2_auto_point1_temp
which is rw. Below this temperature fan stops.
temp1_auto_point2_temp rw The low-temperature limit of the proportional
range. Below this temperature
pwm1 = pwm1_auto_point2_pwm. It can go from
0 degree C to 124 degree C in steps of
4 degree C. Read it out after writing to get
the actual value.
temp1_auto_point3_temp rw Above this temperature fan runs at maximum
speed. It can go from temp1_auto_point2_temp.
It can only have certain discrete values
which depend on temp1_auto_point2_temp and
pwm1_auto_point2_pwm. Read it out after
writing to get the actual value.
temp2_auto_point1_temp rw Must be between 0 degree C and 63 degree C and
it defines the passive cooling temperature.
Below this temperature the fan stops in
the closed loop mode.
temp2_auto_point2_temp rw The low-temperature limit of the proportional
range. Below this temperature
pwm1 = pwm1_auto_point2_pwm. It can go from
0 degree C to 124 degree C in steps
of 4 degree C.
temp2_auto_point3_temp rw Above this temperature fan runs at maximum
speed. It can only have certain discrete
values which depend on temp2_auto_point2_temp
and pwm1_auto_point2_pwm. Read it out after
writing to get actual value.
Module parameters
-----------------
If your board has a BIOS that initializes the amc6821 correctly, you should
load the module with: init=0.
If your board BIOS doesn't initialize the chip, or you want
different settings, you can set the following parameters:
init=1,
pwminv: 0 default pwm output, 1 inverts pwm output.
|